by | Sep 27, 2025
Technical Data Sheet
+. .
Loctite Frekote B-15
Known as Frekote B-15
December 2013
PRODUCT DESCRIPTION Directions for use:
Loctite Frekote B-15 provides the following product 1. Loctite Frekote B-15 can be applied to mold surfaces
characteristics: _ by spraying, brushing, dipping or wiping with a clean, lint
Technology _ Mold Sealer _ free, cotton wiping cloth. When spraying, ensure a dry air
Appearance Clear, colorless”> source is used or use an airless spray system making
Chemical Type Solvent Based Polymer sure the nozzles is 20 to 25 cm from the mold surface.
[Odor SSSSC*SOent Sd 2. Brushing and dipping are effective methods of application,
Cure Room temperature cure but care should be taken to avoid excessive pooling and
Cured Thermal Stability |<400 C to ensure that the part is well drained. Wiping on is the
Application Mold Sealer = best method of application.
Application Temperature|20 to 60 C 7 3. Only a thin wet film is required. It is suggested that small
Specific Benefit No contaminating transfer areas be coated, working progressively from one mold to
# High thermal stability the other, , ,
Seals mold porosity, scratches| 4. Apply 8 of two coats, allowing 30 minutes
imperfect q
crimperfections _________| 5 The final coat will cure within 24 hours at 23 C or the cure
process can be shortened by baking the mold for 60
ito a o minutes at 95 C after ensuring that the mold is dry and all
Paapaae Frekote oe is formulated specifically asa Sealer sovents have flashed off.
for composite and metal molds with micro porosity problems, 6. The mold is now ready to be coated with Frekote mold
small surface scratches or imperfections. {sed in Sengunction release products. Please refer to individual product data
with other Frekote products, Loctite Frekote B-15 sheets for the proper application of the release agent.
provides an excellent base coat enhancing the release ae
ch up
advantages offered. Touch up coats with a sealer should only be applied to areas
where the mold was repaired. On repaired areas apply the
TYPICAL PROPERTIES OF UNCURED MATERIAL same number of sealer and release agent coats like for the
Specific Gravity @ 25 C 0.745 to 0.775" base coating onto new or refurbished molds.
- Loctite Material Specification >
Pash Point S22 =P8 LMS dated December 18, 2002. Test reports for each batch
Release Agent Transfer ques are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
GENERAL INFORMATION . consistency. Special customer specification requirements may
This product is not recommended for use in pure oxygen be coordinated through Henkel Quality.
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Mold Preparation
Cleaning:
Mold surfaces must be thoroughly cleaned and dried. All traces
of prior release must be removed. This may be accomplished
by using Loctite Frekote PMC or other suitable cleaner.
Loctite Frekote 915WB or light abrasives can be used for
heavy build-up.
by | Sep 27, 2025
. casey
(a Chem
Trend
– Release Innovation
Se
|
|
*hoDUCT DATA Ghemlease Mold Cleaner EZ
Description Handling and Storage
Chemlease Mold Cleaner EZ is a special blend of Chemlease Mold Cleaner EZ is flammable and must
HAP free* solvents designed to remove wax and be kept away from heat, sparks, and open flame. The
contaminants from composite molds. Chemlease can should be kept closed when not in use to prevent
Mold Cleaner EZ is ideal for preparing composite mold evaporation of flammable solvents. Store material in a
surfaces for the application of Chemlease mold cool location. Avoid breathing of vapor or spray mist
sealers and releasants. Chemlease Mold Cleaner EZ _ or prolonged contact with skin. Use only with
is also excellent for cleaning brushes and equipment. adequate ventilation. DO NOT take internally. In
confined areas, operators should wear respirators or
*HAPs are not formula constituents of this product. fresh air masks. Industrial grade solvent resistant
Standard manufacturing processes may result in trace gloves should be worn while using Chemlease
quantities [<0 .1%] of HAPs. materials.
Application Packaging
1. Chemlease Mold Cleaner EZ should be applied Chemlease Mold Cleaner EZis available in
to the mold surface with clean, 100% cotton 4-quart (1 liter), 1-gallon (4 liter), 5-gallon
cloths. While the mold surface is still wet, (20 liter) and 55-gallon (208 liter) containers.
vigorously wipe the mold dry with a second clean,
dry, 100% cotton cloth.
2. Frequently exchange saturated cloths with new, Safety Data
clean cloths. Material Safety Data Sheets are available for all
3. Repeat process several times (a minimum of two Chemlease products and should be consulted prior to
cleanings is recommended) until all residues (dirt, Se of the product.
dust, grease, moisture, etc.) are removed.
4. The mold is then ready for application with the
appropriate Chemlease Mold Sealer and/or
Chemlease Mold Release.
NOTE: While the technical information and suggestions for use contained
If you plan to use compounds or glazes, etc., prior to herein are believed to be accurate and reliable, nothing stated in this
applying Chemlease Mold Sealer and/or Chemlease _llletinis to be taken as a warranty either expressed or implied.
Mold Release, be sure to wipe clean with Chemlease
Mold Cleaner EZ after doing so, as most buffing
compounds will not allow Chemlease sealers and
release agents to work properly. Prolonged exposure
on the mold surface (puddling, dipping, etc.) should be
avoided.
Chem-Trend LP.
121608 1445 W. McPherson Park Drive, P.O. Box 860, Howell, Ml 48844.0860
Telephone: 517.546.4520 Facsimile: 517.548.5370 US/Canada: 800.727.7730
www.chemtrend.com Copyright 2004 Chem-Trend L-P., All Rights Reserved
by | Sep 27, 2025
Technical Data Sheet
+4
Loctite Frekote B-15
Known as Frekote B-15
December 2013
PRODUCT DESCRIPTION Directions for use:
Loctite Frekote B-15 provides the following product 1. Loctite Frekote B-15 can be applied to mold surfaces
characteristics: by spraying, brushing, dipping or wiping with a clean, lint
Technology Mold Sealer _ a free, cotton wiping cloth. When spraying, ensure a dry air
[Appearance ___[Clear, colorless _ source is used or use an airless spray system making
Chemical Type [Solvent Based Polymer sure the nozzles is 20 to 25 cm from the mold surface.
[Odor [Sovent 2. Brushing and dipping are effective methods of application,
(Cure [Room temperature cure | but care should be taken to avoid excessive pooling and
Cured Thermal Stability |<400 C to ensure that the part is well drained. Wiping on is the
Application Mold Sealer ae best method of application.
Application Temperature|20 to 60 C oo 3. Only a thin wet film is required. It is suggested that small
Specific Benefit No contaminating transfer areas be coated, working progressively from one mold to
| e High thermal stability ee - a
| * Seals mold porosity, scratches 4. Apply 2 of two coats, allowing 30 minutes
L_______ | _orimperfections _ 5. The final coat will cure within 24 hours at 23 C or the cure
process can be shortened by baking the mold for 60
Loctite Frekote B-15 is formulated specifically as a sealer minutes at 9eie after ensuring that the mold is dry and all
for composite and metal molds with micro porosity problems, 6. The mold is now ready to be coated with Frekote mold
small surface scratches or imperfections. Used in conjunction release products. Please refer to individual product data
with other Frekote products, Loctite Frekote B-15 sheets for the proper application of the release agent.
provides an excellent base coat enhancing the release
advantages offered Mold Touch up
7 Touch up coats with a sealer should only be applied to areas
where the mold was repaired. On repaired areas apply the
TYPICAL PROPERTIES OF UNCURED MATERIAL same number of sealer and release agent coats like for the
Specific Gravity @ 25 C 0.746 to 0.7750" base coating onto new or refurbished molds.
. Loctite Material Specification >
Flash Point – See SDS LMS dated December 18, 2002. Test reports for each batch
Release Agent Transfer aus are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
GENERAL INFORMATION . consistency. Special customer specification requirements may
This product is not recommended for use in pure oxygen _be coordinated through Henkel Quality.
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Mold Preparation
Cleaning:
Mold surfaces must be thoroughly cleaned and dried. Alll traces
of prior release must be removed. This may be accomplished
by using Loctite Frekote PMC or other suitable cleaner.
Loctite Frekote 915WB or light abrasives can be used for
heavy build-up.
a
by | Sep 27, 2025
TechnicalDataSheet
LOCTITE
FREKOTE700-NC
Knownas700-NC
January-2015
PRODUCTDESCRIPTION
LOCTITE
FREKOTE 700-NC providesthefollowing
productcharacteristics:
Technology MoldRelease
Appearance Clear,colorless
LMS
ChemicalType SolventBasedPolymer
Odor Solvent
Cure Romtemperaturecure
CuredThermalStability 400 C
Application ReleaseCoatings
ApplicationTemperature13 to135 C
SpecificBenefit Nochlorinatedsolvents
Highglossfinish
Highslip
Nocontaminatingtransfer
Nomoldbuild-up
LOCTITE
FREKOTE 700-NC offersexcellentrelease
propertiesforthemostdemandingapplicationsandisagreat
all-purposereleaseagent.LOCTITE
FREKOTE700-NC
releasesepoxies,polyesterresins,thermoplastics,rubber
comp ndsandmostothermoldedpolymers.
TYPICALPROPERTIESOFUNCUREDMATERIAL
SpecificGravity@ 25 C 0.755 to0.764
LMS
FlashPoint-SeeSDS
GENERALINFORMATION
Thisproductisnotrecommendedforuseinpureoxygen
and/oroxygenrichsystemsandshouldnotbeselectedas
asealantforchlorineorotherstrongoxidizing materials.
Forsafehandlinginformationonthisproduct,consultthe
SafetyDataSheet(SDS).
MoldPreparation
Cleaning:
Moldsurfacesmustbethor ghlycleanedanddried.Alltraces
ofpriorreleasemustberemoved.Thismaybeaccomplished
byusing Frekote
PMCorothersuitablecleaner. Frekote
915WB orlightabrasivescanbeusedforheavybuild-up.
SealingNew/RepairedMolds:
Occasionally,greenorfreshlyrepairedmoldsarerushedinto
servicepriortocompletecurecausinganincreasedam ntof
freestyreneonthemoldsurface.Freshor”productionline”
repairs,newfiberglassandepoxymoldssh ldbecuredper
manufacturer’sinstructions,usuallyaminimumof2-3weeks
at22 Cbeforestartingfull-scaleproduction.Fullycured
previ slyunusedmoldssh ldbesealedbeforeuse.This
canbeaccomplishedbyapplyingonetotwocoatsof an
appropriate Frekote
moldsealer, followingthedirectionsfor
useinstructions. AllowfullcureoftheappropriateFrekote
moldsealerbeforey applythefirstcoatofLOCTITE
FREKOTE700-NC as tlinedinthedirectionsofuse.
Directionsforuse:
1.LOCTITE
FREKOTE700-NC canbeappliedtomold
surfacesatromtemperatureupto135 Cbyspraying,
brushingorwipingwithacleanlint-free,cloth.When
sprayingensureadryairs rceisusedoruseanairless
spraysystem.Alwaysuseinawellventilatedarea.
2.Wipeorsprayonasmoth,thin,continu s,wet
film. Avoidwipingorsprayingoverthesameareathat
wasjustcoateduntilthesolventhasevaporated.If
spraying,holdnozzle20 to30cmfrommoldsurface.Itis
suggestedthatsmallareasbecoated,working
progressivelyfromonesideofthemoldtotheother.
3.Initially,apply2 to3basecoatsallowing5 to10 minutes
betweencoatsforsolventevaporation .
4.Allowthefinalcoattocurefor15 to20minutesat22 C.
5.Maximumreleaseswillbeobtainedasthemoldsurface
becomesconditionedtoLOCTITE
FREKOTE700-NC
. Performancecanbe enhancedbyre-coatingonce,after
thefirstfewinitialpulls.
6.Whenanyreleasedifficultyisexperienced,theareain
questioncanbe”t ched-up”byre-coatingtheentire
moldsurfaceorjustthoseareaswherereleasedifficultyis
occurring.
7.NOTE: LOCTITE
FREKOTE700-NC ismoisture
sensitive,keepcontainertightlyclosedwhennotinuse.
Theproductsh ldalwaysbeusedinawellventilated
area.
8.Precaution: Usersofclosedmoldsystems(rotomolding)
mustbecertainthatsolventevaporationiscompleteand
thatallsolventvaporshavebeenventilatedfromthemold
cavitypriortoclosingthemold.Anoil-freecompressedair
s rcecanbeusedtoassistinevaporationofsolvents
andventilationofthemoldcavity.
TDSLOCTITE
FREKOTE700-NC , January-2015
MoldTouchup
T chupcoatssh ldonlybeappliedtoareaswherepor
releaseisnoticedandsh ldbeappliedusingthesame
methodasbasecoats.Thiswillreducethepossibilityof
releaseagentorpolymerbuild-up.Thefrequencyoft chups
willdependonthepolymertype,moldconfiguration,and
abrasionparameters.
LoctiteMaterialSpecification
LMS
LMSdated May-10,2006. Testreportsforeachbatchare
availablefortheindicatedproperties. LMStestreportsinclude
selectedQCtestparametersconsideredappropriateto
specificationsforcustomeruse. Additionally,comprehensive
controlsareinplacetoassureproductqualityand
consistency. Specialcustomerspecificationrequirementsmay
becordinatedthr ghHenkel Quality.
Storage
Theproductisclassifiedasflammableandmustbestoredin
anappropriatemannerincompliancewithrelevant
regulations. Donotstorenearoxidizingagentsorcombustible
materials. Storeproductintheunopenedcontainerinadry
location. Storageinformationmayalsobeindicatedonthe
productcontainerlabelling.
OptimalStorage: 8 Cto21 C. Storagebelow8 Cor
greaterthan28 Ccanadverselyaffectproductproperties.
Materialremovedfromcontainersmaybecontaminatedduring
use. Donotreturnproducttotheoriginalcontainer. Henkel
cannotassumeresponsibilityforproductwhichhasbeen
contaminatedorstoredunderconditionsotherthanthose
previ slyindicated. Ifadditionalinformationisrequired,
pleasecontacty rlocalTechnicalServiceCenteror
CustomerServiceRepresentive.
Conversions
( Cx1.8)+32= F
kV/mmx25.4=V/mil
mm/25.4=inches
m/25.4=mil
Nx0.225=lb
N/mmx5.71=lb/in
N/mm x145=psi
MPax145=psi
N m x 8.851= lb in
N mx0.738=lb ft
N mm x0.142=oz in
mPa s=cP
Note:
TheinformationprovidedinthisTechnicalDataSheet(TDS)includingthe
recommendationsforuseandapplicationoftheproductarebasedon r
knowledgeandexperienceoftheproductasatthedateofthisTDS.Theproduct
canhaveavarietyofdifferentapplicationsaswellasdifferingapplicationand
workingconditionsiny renvironmentthatarebeyond rcontrol.Henkelis,
therefore,notliableforthesuitabilityof rproductfortheproductionprocesses
andconditionsinrespectofwhichy usethem,aswellastheintended
applicationsandresults.Westronglyrecommendthaty carry ty rown
priortrialstoconfirmsuchsuitabilityof rproduct.
AnyliabilityinrespectoftheinformationintheTechnicalDataSheetoranyother
writtenororalrecommendation(s)regardingtheconcernedproductisexcluded,
exceptifotherwiseexplicitlyagreedandexceptinrelationtodeathorpersonal
injurycausedby rnegligenceandanyliabilityunderanyapplicablemandatory
productliabilitylaw.
IncaseproductsaredeliveredbyHenkelBelgiumNV,HenkelElectronic
MaterialsNV,HenkelNederlandBV,HenkelTechnologiesFranceSASand
HenkelFranceSApleaseadditionallynotethefollowing:
IncaseHenkelw ldbeneverthelessheldliable,onwhateverlegalgr nd,
Henkel sliabilitywillinnoeventexceedtheam ntoftheconcerneddelivery.
IncaseproductsaredeliveredbyHenkelColombiana,S.A.S.thefollowing
disclaimerisapplicable:
TheinformationprovidedinthisTechnicalDataSheet(TDS)includingthe
recommendationsforuseandapplicationoftheproductarebasedon r
knowledgeandexperienceoftheproductasatthedateofthisTDS.Henkelis,
therefore,notliableforthesuitabilityof rproductfortheproductionprocesses
andconditionsinrespectofwhichy usethem,aswellastheintended
applicationsandresults.Westronglyrecommendthaty carry ty rown
priortrialstoconfirmsuchsuitabilityof rproduct.
AnyliabilityinrespectoftheinformationintheTechnicalDataSheetoranyother
writtenororalrecommendation(s)regardingtheconcernedproductisexcluded,
exceptifotherwiseexplicitlyagreedandexceptinrelationtodeathorpersonal
injurycausedby rnegligenceandanyliabilityunderanyapplicablemandatory
productliabilitylaw.
IncaseproductsaredeliveredbyHenkelCorporation,ResinTechnology
Group,Inc.,orHenkelCanadaCorporation,thefollowingdisclaimeris
applicable:
Thedatacontainedhereinarefurnishedforinformationonlyandarebelievedto
bereliable.Wecannotassumeresponsibilityfortheresultsobtainedbyothers
overwhosemethodswehavenocontrol.Itistheuser’sresponsibilityto
determinesuitabilityfortheuser’spurposeofanyproductionmethodsmentioned
hereinandtoadoptsuchprecautionsasmaybeadvisablefortheprotectionof
propertyandofpersonsagainstanyhazardsthatmaybeinvolvedinthehandling
andusethereof.Inlightoftheforegoing,HenkelCorporationspecifically
disclaimsallwarrantiesexpressedorimplied,includingwarrantiesof
merchantabilityorfitnessforaparticularpurpose,arisingfromsaleoruse
ofHenkelCorporation sproducts.HenkelCorporationspecifically
disclaimsanyliabilityforconsequentialorincidentaldamagesofanykind,
includinglostprofits.Thediscussionhereinofvari sprocessesor
compositionsisnottobeinterpretedasrepresentationthattheyarefreefrom
dominationofpatentsownedbyothersorasalicenseunderanyHenkel
Corporationpatentsthatmaycoversuchprocessesorcompositions.We
recommendthateachprospectiveusertesthisproposedapplicationbefore
repetitiveuse,usingthisdataasaguide.Thisproductmaybecoveredbyoneor
moreUnitedStatesorforeignpatentsorpatentapplications.
Trademarkusage
Exceptasotherwisenoted,alltrademarksinthisdocumentare trademarksof
HenkelCorporationintheU.S.andelsewhere.
denotesatrademark
registeredintheU.S.PatentandTrademarkOffice.
Reference0.1
Americas
+860.571.5100
Europe
+49.89.320800.1800
Asia
+86.21.2891.8863
Forthemostdirectaccesstolocalsalesandtechnicalsupportvisitwww.henkel.com/industrial
by | Sep 27, 2025
TechnicalDataSheet
LOCTITE
FREKOTE700-NC
Knownas700-NC
January-2015
PRODUCTDESCRIPTION
LOCTITE
FREKOTE 700-NC providesthefollowing
productcharacteristics:
Technology MoldRelease
Appearance Clear,colorless
LMS
ChemicalType SolventBasedPolymer
Odor Solvent
Cure Romtemperaturecure
CuredThermalStability 400 C
Application ReleaseCoatings
ApplicationTemperature13 to135 C
SpecificBenefit Nochlorinatedsolvents
Highglossfinish
Highslip
Nocontaminatingtransfer
Nomoldbuild-up
LOCTITE
FREKOTE 700-NC offersexcellentrelease
propertiesforthemostdemandingapplicationsandisagreat
all-purposereleaseagent.LOCTITE
FREKOTE700-NC
releasesepoxies,polyesterresins,thermoplastics,rubber
comp ndsandmostothermoldedpolymers.
TYPICALPROPERTIESOFUNCUREDMATERIAL
SpecificGravity@ 25 C 0.755 to0.764
LMS
FlashPoint-SeeSDS
GENERALINFORMATION
Thisproductisnotrecommendedforuseinpureoxygen
and/oroxygenrichsystemsandshouldnotbeselectedas
asealantforchlorineorotherstrongoxidizing materials.
Forsafehandlinginformationonthisproduct,consultthe
SafetyDataSheet(SDS).
MoldPreparation
Cleaning:
Moldsurfacesmustbethor ghlycleanedanddried.Alltraces
ofpriorreleasemustberemoved.Thismaybeaccomplished
byusing Frekote
PMCorothersuitablecleaner. Frekote
915WB orlightabrasivescanbeusedforheavybuild-up.
SealingNew/RepairedMolds:
Occasionally,greenorfreshlyrepairedmoldsarerushedinto
servicepriortocompletecurecausinganincreasedam ntof
freestyreneonthemoldsurface.Freshor”productionline”
repairs,newfiberglassandepoxymoldssh ldbecuredper
manufacturer’sinstructions,usuallyaminimumof2-3weeks
at22 Cbeforestartingfull-scaleproduction.Fullycured
previ slyunusedmoldssh ldbesealedbeforeuse.This
canbeaccomplishedbyapplyingonetotwocoatsof an
appropriate Frekote
moldsealer, followingthedirectionsfor
useinstructions. AllowfullcureoftheappropriateFrekote
moldsealerbeforey applythefirstcoatofLOCTITE
FREKOTE700-NC as tlinedinthedirectionsofuse.
Directionsforuse:
1.LOCTITE
FREKOTE700-NC canbeappliedtomold
surfacesatromtemperatureupto135 Cbyspraying,
brushingorwipingwithacleanlint-free,cloth.When
sprayingensureadryairs rceisusedoruseanairless
spraysystem.Alwaysuseinawellventilatedarea.
2.Wipeorsprayonasmoth,thin,continu s,wet
film. Avoidwipingorsprayingoverthesameareathat
wasjustcoateduntilthesolventhasevaporated.If
spraying,holdnozzle20 to30cmfrommoldsurface.Itis
suggestedthatsmallareasbecoated,working
progressivelyfromonesideofthemoldtotheother.
3.Initially,apply2 to3basecoatsallowing5 to10 minutes
betweencoatsforsolventevaporation .
4.Allowthefinalcoattocurefor15 to20minutesat22 C.
5.Maximumreleaseswillbeobtainedasthemoldsurface
becomesconditionedtoLOCTITE
FREKOTE700-NC
. Performancecanbe enhancedbyre-coatingonce,after
thefirstfewinitialpulls.
6.Whenanyreleasedifficultyisexperienced,theareain
questioncanbe”t ched-up”byre-coatingtheentire
moldsurfaceorjustthoseareaswherereleasedifficultyis
occurring.
7.NOTE: LOCTITE
FREKOTE700-NC ismoisture
sensitive,keepcontainertightlyclosedwhennotinuse.
Theproductsh ldalwaysbeusedinawellventilated
area.
8.Precaution: Usersofclosedmoldsystems(rotomolding)
mustbecertainthatsolventevaporationiscompleteand
thatallsolventvaporshavebeenventilatedfromthemold
cavitypriortoclosingthemold.Anoil-freecompressedair
s rcecanbeusedtoassistinevaporationofsolvents
andventilationofthemoldcavity.
TDSLOCTITE
FREKOTE700-NC , January-2015
MoldTouchup
T chupcoatssh ldonlybeappliedtoareaswherepor
releaseisnoticedandsh ldbeappliedusingthesame
methodasbasecoats.Thiswillreducethepossibilityof
releaseagentorpolymerbuild-up.Thefrequencyoft chups
willdependonthepolymertype,moldconfiguration,and
abrasionparameters.
LoctiteMaterialSpecification
LMS
LMSdated May-10,2006. Testreportsforeachbatchare
availablefortheindicatedproperties. LMStestreportsinclude
selectedQCtestparametersconsideredappropriateto
specificationsforcustomeruse. Additionally,comprehensive
controlsareinplacetoassureproductqualityand
consistency. Specialcustomerspecificationrequirementsmay
becordinatedthr ghHenkel Quality.
Storage
Theproductisclassifiedasflammableandmustbestoredin
anappropriatemannerincompliancewithrelevant
regulations. Donotstorenearoxidizingagentsorcombustible
materials. Storeproductintheunopenedcontainerinadry
location. Storageinformationmayalsobeindicatedonthe
productcontainerlabelling.
OptimalStorage: 8 Cto21 C. Storagebelow8 Cor
greaterthan28 Ccanadverselyaffectproductproperties.
Materialremovedfromcontainersmaybecontaminatedduring
use. Donotreturnproducttotheoriginalcontainer. Henkel
cannotassumeresponsibilityforproductwhichhasbeen
contaminatedorstoredunderconditionsotherthanthose
previ slyindicated. Ifadditionalinformationisrequired,
pleasecontacty rlocalTechnicalServiceCenteror
CustomerServiceRepresentive.
Conversions
( Cx1.8)+32= F
kV/mmx25.4=V/mil
mm/25.4=inches
m/25.4=mil
Nx0.225=lb
N/mmx5.71=lb/in
N/mm x145=psi
MPax145=psi
N m x 8.851= lb in
N mx0.738=lb ft
N mm x0.142=oz in
mPa s=cP
Note:
TheinformationprovidedinthisTechnicalDataSheet(TDS)includingthe
recommendationsforuseandapplicationoftheproductarebasedon r
knowledgeandexperienceoftheproductasatthedateofthisTDS.Theproduct
canhaveavarietyofdifferentapplicationsaswellasdifferingapplicationand
workingconditionsiny renvironmentthatarebeyond rcontrol.Henkelis,
therefore,notliableforthesuitabilityof rproductfortheproductionprocesses
andconditionsinrespectofwhichy usethem,aswellastheintended
applicationsandresults.Westronglyrecommendthaty carry ty rown
priortrialstoconfirmsuchsuitabilityof rproduct.
AnyliabilityinrespectoftheinformationintheTechnicalDataSheetoranyother
writtenororalrecommendation(s)regardingtheconcernedproductisexcluded,
exceptifotherwiseexplicitlyagreedandexceptinrelationtodeathorpersonal
injurycausedby rnegligenceandanyliabilityunderanyapplicablemandatory
productliabilitylaw.
IncaseproductsaredeliveredbyHenkelBelgiumNV,HenkelElectronic
MaterialsNV,HenkelNederlandBV,HenkelTechnologiesFranceSASand
HenkelFranceSApleaseadditionallynotethefollowing:
IncaseHenkelw ldbeneverthelessheldliable,onwhateverlegalgr nd,
Henkel sliabilitywillinnoeventexceedtheam ntoftheconcerneddelivery.
IncaseproductsaredeliveredbyHenkelColombiana,S.A.S.thefollowing
disclaimerisapplicable:
TheinformationprovidedinthisTechnicalDataSheet(TDS)includingthe
recommendationsforuseandapplicationoftheproductarebasedon r
knowledgeandexperienceoftheproductasatthedateofthisTDS.Henkelis,
therefore,notliableforthesuitabilityof rproductfortheproductionprocesses
andconditionsinrespectofwhichy usethem,aswellastheintended
applicationsandresults.Westronglyrecommendthaty carry ty rown
priortrialstoconfirmsuchsuitabilityof rproduct.
AnyliabilityinrespectoftheinformationintheTechnicalDataSheetoranyother
writtenororalrecommendation(s)regardingtheconcernedproductisexcluded,
exceptifotherwiseexplicitlyagreedandexceptinrelationtodeathorpersonal
injurycausedby rnegligenceandanyliabilityunderanyapplicablemandatory
productliabilitylaw.
IncaseproductsaredeliveredbyHenkelCorporation,ResinTechnology
Group,Inc.,orHenkelCanadaCorporation,thefollowingdisclaimeris
applicable:
Thedatacontainedhereinarefurnishedforinformationonlyandarebelievedto
bereliable.Wecannotassumeresponsibilityfortheresultsobtainedbyothers
overwhosemethodswehavenocontrol.Itistheuser’sresponsibilityto
determinesuitabilityfortheuser’spurposeofanyproductionmethodsmentioned
hereinandtoadoptsuchprecautionsasmaybeadvisablefortheprotectionof
propertyandofpersonsagainstanyhazardsthatmaybeinvolvedinthehandling
andusethereof.Inlightoftheforegoing,HenkelCorporationspecifically
disclaimsallwarrantiesexpressedorimplied,includingwarrantiesof
merchantabilityorfitnessforaparticularpurpose,arisingfromsaleoruse
ofHenkelCorporation sproducts.HenkelCorporationspecifically
disclaimsanyliabilityforconsequentialorincidentaldamagesofanykind,
includinglostprofits.Thediscussionhereinofvari sprocessesor
compositionsisnottobeinterpretedasrepresentationthattheyarefreefrom
dominationofpatentsownedbyothersorasalicenseunderanyHenkel
Corporationpatentsthatmaycoversuchprocessesorcompositions.We
recommendthateachprospectiveusertesthisproposedapplicationbefore
repetitiveuse,usingthisdataasaguide.Thisproductmaybecoveredbyoneor
moreUnitedStatesorforeignpatentsorpatentapplications.
Trademarkusage
Exceptasotherwisenoted,alltrademarksinthisdocumentare trademarksof
HenkelCorporationintheU.S.andelsewhere.
denotesatrademark
registeredintheU.S.PatentandTrademarkOffice.
Reference0.1
Americas
+860.571.5100
Europe
+49.89.320800.1800
Asia
+86.21.2891.8863
Forthemostdirectaccesstolocalsalesandtechnicalsupportvisitwww.henkel.com/industrial
by | Sep 27, 2025
1726 Floradale Ave., So. El Monte, CA 91733 | 626.443.8983 | sales@FinishKare.com | FinishKare.com
Product Data Sheet
1000P
Hi Low Paste Wax
Premium Mold Release Wax
Description
Finish Kare’s 1000P Hi Low Paste Wax is one of
our very popular product . It is part of the 1000 Mold Release
Wax Series, each formulated with a unique blend of synthetic
waxes and solvents to get specifically desired results.
1000P does exceptionally well in high exothermic conditions
and provides easy multiple releases.
Features & Benefits
High Temp Tolerance
Withstands high temperature exothermic reactions
of resins and does multiple releases easily.
Good for up to 275 F or 135 C.
Unique Wax Makeup
Contains carnauba wax, synthetic waxes and high
temperature resistant resins for effective multiple
releases of composite parts.
High Gloss Finish
Buffing out the final coat will result in a high gloss
finish
The hard, shiny film protects the molds from
intensive wear and heat and creates smoother,
shinier parts
Clean & Seal
Prior to any mold release wax application, we highly
recommend all molds be cleaned and sealed using our #69
Mold Cleaner and Stripper or #135 80 for a deeper clean and
our #86 Seal Kote to seal up any porosity.
Application Process
Step 1: Apply # 1000P, Hi Low Mold Release Wax in Five (5)
separate applications. Make sure that each coat is dry prior to
wiping. Please criss cross each application for assuring the
complete coverage. Apply wax in a circular motion to work the
wax in.
Step 2: Allow 30 minutes to set after the final wipe. Then re
wipe, pour the first part and release it.
Step 3: After releasing the part gently wipe the mold, then
apply one more coat of wax and release one more part.
AT THIS POINT, MOLD IS CURED TO THE POINT THAT
MULTIPLE RELEASES ARE POSSIBLE.
***Additional Release Tricks***
When a part gets a little hard to pull, apply one coat of
#1000L, Hi Low Liquid Wax, let it dry and wipe lightly. Run
more parts and apply # 1000L as needed. Use of # 1000L helps
in preventing wax buildup and thus helps in multiple releases.
Safety Data Sheet
Safety Date Sheets are available for all Finish Kare products
and should be consulted prior to use
Storage and Shelf Life
Store tightly closed container in a dry, cool place that is well
ventilated and below 46 C /104 F. Do not handle or store
near open flame, heat or other sources of ignition. Shelf life is
1 years from date of shipment.
IMITATIONS OF LIABILITY
To the best of our knowledge, the data presented here is true and accurate, but is
subject to change without prior notice. User is kindly requested to contact Finish Kare
Products to verify the correctness before specifying or ordering. Since we don t know
how the product will be used we cannot assume any responsibility for its use,
performance, or any injuries resulting from its use. Liability, if any, is limited to
replacement of defective product. No warranty or guarantee of any kind is expressed or
implied by Finish Kare Products, Inc.
by | Sep 27, 2025
1726 Floradale Ave., So. El Monte, CA 91733 | 626.443.8983 | sales@FinishKare.com | FinishKare.com
Product Data Sheet
1000L
Hi Low Liquid Wax
Interphase Wax Liquid Gold
Description
The charm of 1000L is it allows you to get even more releases
in a multiple release cycle with less effort. It reduces wax build
up and surface tension, while redistributing and smoothing
out the existing waxes to prepping your mold to release the
next part.
Once the pulls start to get a little harder instead of doing a
clean re layup, simply apply 1000L Liquid Wax and continue
releasing.
Features & Benefits
Increased Number of Releases
Instead of reapplying paste wax, 1000L lets you get
more releases from the same initial layup
It also increases protection of the molds and helps to
prolong the multiple release cycle
Saves Time
Liquid Wax dries quickly, which cuts down on wait
time and lets your team get back to work faster
Minimal Elbow Grease Required
Due to its liquid nature 1000L is quick to apply.
The unique solvents do the heavy lifting by easily
liquefying the mold release waxes which requires
very little effort to apply
Clean & Seal
Prior to any mold release wax application, we highly
recommend all molds be cleaned and sealed using our #69
Mold Cleaner and Stripper or #135 80 for a deeper clean and
our #86 Seal Kote to seal up any porosity.
Application Process
Once the mold is properly broken in using a paste wax, like
our #1000P Hi Low Paste Wax, then 1000L can be applied.
Step 1: Spread evenly and agitate lightly
Step 2: Allow 15 30 mins to dry and then wipe.
Repeat 1 or 2 more times and then continue releasing. Repeat
this process again once pulls start to get difficult.
This product contains sufficient waxes to continue easy
demolding and multiple releases. It reactivates and spreads
the paste wax deterring any possible wax build up or surface
tension.
Safety Data Sheet
Safety Date Sheets are available for all Finish Kare products
and should be consulted prior to use.
Storage and Shelf Life
Store tightly closed container in a dry, cool place that is well
ventilated. Do not handle or store near open flame, heat or
other sources of ignition. Shelf life is 6 months after opening.
LIMITATIONS OF LIABILITY
To the best of our knowledge, the data presented here is true and accurate, but is
subject to change without prior notice. User is kindly requested to contact Finish Kare
Products to verify the correctness before specifying or ordering. Since we don t know
how the product will be used we cannot assume any responsibility for its use,
performance, or any injuries resulting from its use. Liability, if any, is limited to
replacement of defective product. No warranty or guarantee of any kind is expressed or
implied by Finish Kare Products, Inc.
by | Sep 27, 2025
@ Finish are
2 ep SE ENS SE TR EES
1000L Clean & Seal
Prior to any mold release wax application, we highly
Hi-Low Liq u id Wax recommend all molds be cleaned and sealed using our #69
Mold Cleaner and Stripper or #135-80 for a deeper clean and
our #86 Seal Kote to seal up any porosity.
ae
Application Process
2 Once the mold is properly broken in using a paste wax, like
as 5 our #1000P Hi-Low Paste Wax, then 1000L can be applied.
| (eesy Step 1: Spread evenly and agitate lightly
| me | Step 2: Allow 15-30 mins to dry and then wipe.
Litt } Repeat 1 or 2 more times and then continue releasing. Repeat
this process again once pulls start to get difficult.
i aeeemenenemenmetl This product contains sufficient waxes to continue easy
a demolding and multiple releases. It reactivates and spreads
Interphase Wax Lquld Gold the paste wax deterring any possible wax build up or surface
_ tension.
Description
The charm of 1000L is it allows you to get even more releases Safety Data Sheet
in a multiple release cycle with less effort. It reduces wax build Safety Date Sheets are available for all Finish Kare products
up and surface tension, while redistributing and smoothing and should be consulted prior to use
out the existing waxes to prepping your mold to release the
next part. Storage and Shelf Life
. . Store tightly closed container in a dry, cool place that is well
Once the pulls start to get a little harder instead of doing a ventilated. Do not handle or store near open flame, heat or
clean re-layup, simply apply 10001 Liquid Wax and continue other sources of ignition. Shelf life is 6 months after opening.
releasing.
LIMITATIONS OF LIABILITY
. To the best of our knowledge, the data presented here is true and accurate, but is
Features & Benefits subject to change without prior notice. User is kindly requested to contact Finish Kare
Increased Number of Releases Products to verify the correctness before specifying or ordering. Since we don t know
. – how the product will be used we cannot assume any responsibilty for its use,
Instead of reapplying paste wax, 10001 lets you get performance, or any injuries resulting from its use. Liability if any, is limited to
more releases from the same initial layup replacement of defective product. No warranty or guarantee of any kind is expressed or
* It also increases protection of the molds and helps to Implied by Finish Kare Products, inc.
prolong the multiple release cycle
Saves Time
* Liquid Wax dries quickly, which cuts down on wait
time and lets your team get back to work faster
Minimal Elbow Grease Required
Due toits liquid nature 1000L is quick to apply.
e The unique solvents do the heavy lifting by easily
liquefying the mold release waxes which requires
very little effort to apply
|p SES SS SESS SE SES ESSE SESS SS SS
1726 Floradale Ave., So. El Monte, CA 91733 | 626.443.8983 | sales@FinishKare.com | FinishKare.com
by | Sep 27, 2025
1726 Floradale Ave., So. El Monte, CA 91733 | 626.443.8983 | sales@FinishKare.com | FinishKare.com
Product Data Sheet
1000L
Hi Low Liquid Wax
Interphase Wax Liquid Gold
Description
The charm of 1000L is it allows you to get even more releases
in a multiple release cycle with less effort. It reduces wax build
up and surface tension, while redistributing and smoothing
out the existing waxes to prepping your mold to release the
next part.
Once the pulls start to get a little harder instead of doing a
clean re layup, simply apply 1000L Liquid Wax and continue
releasing.
Features & Benefits
Increased Number of Releases
Instead of reapplying paste wax, 1000L lets you get
more releases from the same initial layup
It also increases protection of the molds and helps to
prolong the multiple release cycle
Saves Time
Liquid Wax dries quickly, which cuts down on wait
time and lets your team get back to work faster
Minimal Elbow Grease Required
Due to its liquid nature 1000L is quick to apply.
The unique solvents do the heavy lifting by easily
liquefying the mold release waxes which requires
very little effort to apply
Clean & Seal
Prior to any mold release wax application, we highly
recommend all molds be cleaned and sealed using our #69
Mold Cleaner and Stripper or #135 80 for a deeper clean and
our #86 Seal Kote to seal up any porosity.
Application Process
Once the mold is properly broken in using a paste wax, like
our #1000P Hi Low Paste Wax, then 1000L can be applied.
Step 1: Spread evenly and agitate lightly
Step 2: Allow 15 30 mins to dry and then wipe.
Repeat 1 or 2 more times and then continue releasing. Repeat
this process again once pulls start to get difficult.
This product contains sufficient waxes to continue easy
demolding and multiple releases. It reactivates and spreads
the paste wax deterring any possible wax build up or surface
tension.
Safety Data Sheet
Safety Date Sheets are available for all Finish Kare products
and should be consulted prior to use.
Storage and Shelf Life
Store tightly closed container in a dry, cool place that is well
ventilated. Do not handle or store near open flame, heat or
other sources of ignition. Shelf life is 6 months after opening.
LIMITATIONS OF LIABILITY
To the best of our knowledge, the data presented here is true and accurate, but is
subject to change without prior notice. User is kindly requested to contact Finish Kare
Products to verify the correctness before specifying or ordering. Since we don t know
how the product will be used we cannot assume any responsibility for its use,
performance, or any injuries resulting from its use. Liability, if any, is limited to
replacement of defective product. No warranty or guarantee of any kind is expressed or
implied by Finish Kare Products, Inc.
by | Sep 27, 2025
DESCRIPTION:
Icing Pourable Brushable Polyester Finishing Putty is the original, best selling polyester finishing putty that
spreads smoothly, self levels, and dries to an exceptionally easy to sand finish. Icing provides great adhesion and
is tack free and stain free.
PART NUMBERS:
26006 Icing 24 fl. oz. tube 6 tubes / case 12 lbs / case
26011 Icing 30 fl. oz. pumptainer bottle 6 bottles / case 16 lbs / case
Form: TDSUSC26006 PG 1 of 2 Rev: 02/11 U.S. Chemical & Plastics 600 Nova Dr. SE Massillon, OH 44646 Tel: 800-321-0672
www.USChem.com
TTEECCHHNNIICCAALL DDAATTAA SSHHEEEETT IIcciinngg
PRODUCT: Icing Pourable Brushable Polyester Finishing Putty
TECHNICAL CALLS: 1-800-321-0672
TYPICAL SUBSTRATES:
Metal Aluminum Fiberglass Body Filler Wood 2K Primers
Aged, sanded OEM Topcoats Galvanized and other zinc-coated steel
SMC can be used for cosmetic repairs. For structural repairs prone to high degrees of stress and flexibility,
use an SMC repair product. For flexible plastics use PRO-FLEX 26037.
SURFACE PREPARATION:
1. Clean surface. Remove all dirt, oil, grease and wax with a cleaning solvent such as 1240-1 Wax,
Grease & Silicone Remover.
2. Make sure surface is dry before repairing.
3. Use 80 180 grit disc to featheredge paint for good mechanical adhesion.
MIXING:
For best results, bring putty and provided hardener to room temperature (minimum temperature 68 F).
Knead hardener tube before use. Place a 4 diameter puddle of putty on a clean mixing surface (we
recommend a non-absorbent plastic mixing board) and add a ribbon of cream hardener from edge to
edge across the center of the putty puddle (puddles larger than 4 will require additional hardener); or
measure hardener at 2% by weight a 50-1 ratio. Mix thoroughly with a plastic spreader, using a folding
motion, until uniform color is achieved. At room temperature (68 F) approximate setting time is 3-5
minutes.
MIX
PRODUCT USES:
Use for minor body work and surface imperfections (1/8 thick or less) such as sand scratches, chips, scratches and
pinholes. Ideal for use as a finish coat over body filler.
APPLICATION:
1. Using a plastic spreader, apply a thin layer of putty to surface, using firm pressure for maximum
adhesion.
2. Apply additional layers, building up damaged area higher than the surrounding surface to allow for
sanding of the putty. Do not apply over fresh or uncured coatings.
FINISHING:
When material has hardened, in approximately 15 minutes, sand with 100 – 180 grit sandpaper followed by
220 – 400 grit if desired.
SPECIAL NOTES: May be intermixed with any USC Body Filler product except All-Metal.
TECHNICAL INFORMATION :
Appearance as Packaged: Off-White
VOC Packaged: 281 g/l
Applied: 2.2 g/l
Weight Per Gallon (Density): 9.5 pounds/gallon (Average)
Maximum Recommended Thickness (sanded): 1/8
Viscosity @ 77
F: 18,000 cps
Gel Time @ 77
F: 4.0 5.0 minutes
Shore D Hardness Values @ 24 hours: 55-60
Sanding Time @ 77
o
F: 15 minutes
Maximum Heat: 200 F for 30 minutes
Catalyst Required: Benzoyl Peroxide
Catalyzation Ratio: 2% by weight (50:1 ratio)
Exotherm Temperature: 220 F (Average)
Tack Free Time: 10 – 15 minutes
HEALTH & SAFETY:
Read all warnings, first aid and safety for all components before using. Keep out of reach of children and
animals. Protect hands with impervious rubber gloves. Wear face, skin and eye protection. When
sanding, we recommend the use of a respiratory covering device to protect from dust (MSA mask P/N
459029 with MSA cartridge 464029 or equivalent). When using power equipment, refer to power tool
manufacturer s recommendations for safety equipment. USC products are for industrial use by trained
professionals only.
Emergency Medical or Spill Control Information:
In U.S. or Canada call CHEMTREC at 1-800-424-9300
Form: TDSUSC26006 PG 2 of 2 Rev: 02/11 U.S. Chemical & Plastics 600 Nova Dr. SE Massillon, OH 44646 Tel: 800-321-0672
www.USChem.com
TOPCOATING:
May be topcoated with polyester, 2K urethane or 1K primer. Refer to paint manufacturer s instructions for topcoat
application.
ASSOCIATED MSDS : Putty: Icing-26014 Hardener: Cream Hardener
