by | Sep 27, 2025
22695 Old Canal Road, Yorba Linda, CA 92887 p 714.279.9928 f 714.279.0307
MATERIAL SPECIFICATION
To: Revchem Bloomington
2720 S. Willow Ave
Bloomington, CA 92316
Attn: Russ Tell
Part Number 564381
Part Description 35.5 Rubber Squeegee
Material Natural Rubber
Tensile 1160 psi
Elongation 200%
Hardness 70-75 Shore A
Compression Set 50% max
Heat aged, test method D573, 70 hours at 70 C
Change in tensile strenth +/-30%
Change in elongation -50% max
Change in hardness +/-15 points
Pacifictech Molded Products, Inc. Date: February 10, 2025
by | Sep 27, 2025
Property
Test
Method
Value
Uncured Product
23 +/- 2 C and 50 +/-5% humidity
Color Pale Yellow
Cure Profile
23+/-2 C and 50+/-5%
humidity
Density
BS ISO
2781
0.83 g/cm3
Flash Point C
BS 2000-
34
28 C
Odour Alcohol
Rheology Liquid
Tack Free Time / Skin
Formation at 23 C/73 F
15 min
Viscosity Mixed Brookfield1 cP
Storage
Max Storage Temperature 25 C / 77 F
Min Storage Temperature 5 C / 41 F
Shelf Life 18 mths
Primer No. 6
Primer
Description
This is a specially formulated silicone based primer for use with a
wide range of CHT 1K Condensation / Moisture curing RTV
silicone sealants. This primer imparts good adhesion to most
metals. It is recommended as a primer for use on non-porous
surfaces. For all new applications, it is recommended that
customers carry out small-scale tests to determine the suitability
of the primer and the strength of bond produced.
Key Features
Aerospace approved
Suitable for use with CHT adhesives
Suitable for non porous surfaces
For use with most metals
Key Applications
Rolls Royce MSRR1064
Application
Primer for condensation cure 1 part adhesives on metal
substrates. Not suitable for polycarbonate and acrylic
Use and Cure Information
This primer contains solvents which are classified as hazardous
under current regulations. Users should read the Safety Data
Sheets for this product carefully before use. Surfaces to be
bonded should be dry and free from grease, oil, dust and release
agents. Non-porous substrates, should be solvent degreased prior to application. The primer should be applied with a lint-free cloth or
paintbrush and allowed to dry thoroughly at room temperature for a minimum time equal to the tack free time given in this document, before
applying the sealant. Drying should be carried out in a well-ventilated area. Do not leave longer than 2 hours. The drying/curing time is
dependent on the ambient temperature and humidity. Heat should not be applied to accelerate the drying cycle. Over-application of the
primer will result in poor adhesion. As a guide, one litre of Primer should be sufficient for approximately 15 m . It is absolutely important to
check the compatibility in preliminary tests if unknown substrates are used.
Health & Safety
Safety
Please observe the safety data sheets and the safety statements on the container labels when handling our products. The dangerous goods
regulations and the accident prevention regulations of the professional associations must be particularly observed. Keep the safety data
sheet of the applied product at hand since it provides useful instructions for the safe use and disposal of the product as well as for actions to
be taken in case of accidents.
Revision Date 01 Mar 2024
Revision No 2
Download Date 22 Oct 2024
TECHNICAL DATA SHEET
The content set out in the technical data sheet does not contain information upon which you should rely. It is provided for general information purposes only and does not constitute a product
specification. You must obtain professional or specialist advice before taking any action based on the information provided in the technical data sheet.
CHT make reasonable efforts to ensure that information set out in the technical data sheet is complete, accurate, and up-to-date. CHT do not, however, make any representations, warranties or
guarantees (whether express or implied) that information set out in the technical data sheet is complete, accurate, or up-to-date or that the product will be suitable for your requirements. You
should carry out your own testing to determine the applicability of such information and whether the product will be suitable. CHT reserve the right to modify the technical data sheet at any time.
The CHT technical service department is available to offer further information and advice and should it be needed to look at modifying current products or custom formulate a new one to meet
your specific requirements. Please contact the technical service department.
CHT Germany GmbH: Postfach 12 80, 72002 T bingen, Bismarckstra e 102, 72072 T bingen, Germany
Telephone: 07071/154-0, Fax: 07071/154-290, Email: info@cht.com, Homepage: www.cht.com / www.cht-silicones.com
by | Sep 27, 2025
WA ISO 9001:2008 Ya
7 ranscendia Certiec Compary emt
DESCRIPTION:
Oriented Polyester films are rigid plastics that are strong, smooth to matte surfaces. Available in sheets and rolls
durable, dimensionally stable, and have anti-curl with widths from .5″ to 92″ with 3″, 6″, and 10″ cores.
properties. They are suitable for graphics, packaging, Gauges are available from .00032″ to .014″, and special
electrical and industrial applications. Oriented Polyester surface treatments include ink adhesion, slip, and anti-
films are available in super-clear to clear matte, and static.
CHARACTERISTICS:
* Easily printed with water or solvent based inks using * Excellent chemical and abrasion resistance and
flexography, offset lithography, and screen printing. temperature resistance.
* Can be folded, sheeted, die cut, grommeted, glued, * General inertness and free of additives.
and sewn.
TECHNICAL DATA:
MECHANICAL PROPERTIES TYPICAL VALUES TEST CONDITIONS TEST METHOD-ASTM
MD >20 kg/mm?
TENSILE STRENGTH TD 320 kg/mm? 25 C D-882-64
MD 100 to 120%
ELONGATION AT BREAK 882-1
TD 100 to 120% esr D-882-84
2
F-5 VALUE MD 9.5 kg/mm 25 C D-882-64
TD 9.5 kg/mm?
IMPACT STRENGTH 400 g cm/cm? 25 C. 2541 film D-1709-62
TEAR STRENGTH – PROPAGATING 20 g/mil 25 C. 2541 film D-1922-61
ELMENDOPF INITIAL – GRAVES 800 g/mil 25 C. 254 film _ D-1004-66
BURSTING STRENGTH >5 kg/cm? 25 C. 2541 film D-774-63
FOLDING ENDURANCE 10 cycle 25 C. 25,1 film D-2176-63
PHYSICAL PROPERTIES
DENSITY 1.390 to 1.405 g/cm? 25 C D-1505-63
MOISTURE ABSORPTION .05 wt% 23 C, 24 hr D-570-63
WATER VAPOR 25 g/m*/24 hr 251 film @ 40 C. @ 100% R.H. E-98-66
TRANSMISSION RATE: OXYGEN 40 cm*/m#/24 hr 25u film @ 25 C.@ 1 atm D-1434-66
COEFFICIENT OF KINETIC 5
FRICTION: FILM/FILM STATIC OF 03 1008 ere D-1894-68
THERMAL PROPERTIES
MELTING POINT 280 C
SOFTENING POINT 250 C
HEAT SHRINKAGE 2.0 % 150 C X 30 min D-2305-67
SERVICE TEMPERATURE -70 to +150 C
SPECIFIC HEAT 0.3 cal g C 25 C
COEFFICIENT OF LINEAR THERMAL EXPANSION 3×10 cm/em/ C 30 C to 50 C D-696-44
COEFFICIENT OF THERMAL CONDUCTIVITY 3×10″ cal/om sec C
ELECTRICAL PROPERTIES
DIELECTRIC STRENGTH 7,500 volts/mil 25 C 60hz D-149-64
DIELECTRIC CONSTANT 33 25 C 60hz D-150-65
DIELECTRIC DISSIPATION 0.0025 25 C 60hz D-150-65
VOLUME RESISTIVITY 10 ohm-cm 25 C D-257-66 & D-2305-67
SURFACE RESISTIVITY 10″? ohm-cm/cm 23 C 80% RH. D-257-66
Note: The stated values are typical data and are not specification of guarantee. Transcendia suggests that purchaser confirm product compatibility prior to use of this product .
Stated values are believed to be accurate, but all information is presented without guarantee or responsibility on the part of Transcendia.
CORPORATE HEADQUARTERS 9201 W. Belmont Avenue | Franklin Park, IL 60131
USA 800.618.5060 | 847.678.1800 main | 847.233.0199 fax
CAN 800.268.4108 | 416.292.6000 main | 416.292.7399 fax
TRANSCENDIA.COM 2016 Transcendia Inc. All Rights Reserved.
by | Sep 27, 2025
For technical information call 800.992.2424 or 203.743.4447
For product sales: CT 800.442.3424, CA 800.771.8161, IL 800.447.4866, Canada 800.307.2199
www.miller-stephenson.com
MS-242N
Quik-Freeze
Description
Miller-Stephenson s Quik-Freeze
(MS-242N) is a 14oz
aerosol product that is designed for convenient use in
many industrial applications. It contains HFC 134a
propellant which is a non-ozone depleting chemical.
MS-242N provides a rapid method of cooling small
electronic components. This product is utilized to locate
intermittent malfunctions in electronic equipment.
Applying the Quik-Freeze
will have no effect on
components operating properly but faulty components will
be shocked into failure mode and immediately identified.
MS-242N freezes small areas to -55 F/-48 C.
ADVANTAGES:
Nonconductive
Nonflammable
Odorless
Low order of toxicity
Compatible with most plastics, elastomers, and
metals
Leaves no residue
NSN 6850-01-333-1841
Quik-Freeze
is recommended for:
Heat-cold intermittence testing of electronic
components.
Protection of expensive components during
soldering/desoldering.
Low temperature circuit testing.
Nondestructive testing of electronic and
electromechanical systems.
PHYSICAL PROPERTIES OF HFC 134a:
Molecular weight .. 102.03
Boiling point ..-15.7 F/-26.5 C
Vapor pressure 96.5 psia @ 77 F/25 C
Density .. .1.21 @ 77 F/25 C
VOC . exempt
ODP .. .zero
Safety Data Sheet (SDS) is available upon request
1308-9K
The recommendation made here with and the information set forth with respect to the
performance or use of our products are believed, but not warranted to be accurate. The products
discussed are sold without warranty, as to fitness or performance, express or implied and upon
condition that purchasers shall make their own test to determine suitability of such products for
their particular purposes. Likewise, statements concerning the possible uses of our products are
not intended as recommendations to use our products in the infringement of any patent.
by | Sep 27, 2025
Komar
| Alliance
Threads, Papers, Chemicals and Supplies
REINFORCED ASPHALTIC KRAFT 3560
Technical Data Sheet
Composition
| Kraft Paper (Top Sheet) Natural Recycled Kraft 30,0#/3000 Sq. Ft.
shat ORTHO F
110 1/0 Denier 1-1-1
MD Reinforcement Fiberglass | 1.094/3000 $9, Ft.
CD Reinforcement Fiberglass BaD Retietion: Ls scars
1.37#/3000 Sq, Ft.
Physical Properties
Basset
Ba
Tensile Strength ASTM D-828 58 Ibs/in MD
a
The technical data presented in this Technical Data Sheet are typical physical properties observed. and
recorded, not limiting technical specifications. These values can range and data is an observed average
for Informational purposes. Physical properties listed above are based upon statistical averages. Values
for weights and caliper can vary + 10%
6900 Washington Blvd. – Montebello, CA 90640
(800) 872-7397 www.komar.com Fax (323) 890-3003
by | Sep 27, 2025
Filter :
fc : PRODUCT SPECIFICATION SHEET
MODEL: PA15 standararinersiass media
_ Weight of 15 GRAMS/SQ.FT.
Ideal for use in a variety of crossdraft applications.
98.66% average spray removal efficiency.
ie __ -Meets the testing and performance requirements of NESHAP 40CFR63 Subpart 6H.***
pan fn
| -Initial pressure drop of .02 @ 150 FPM.
-Paint holding capacity of 1.3 LBS/SQ.FT. of media.
-Rated UL 900 for flammability.
-Thermally stable to 212 degrees F.
-Typically land-fillable (contains no known hazardous materials).
-Compression rolled and packed to reduce storage and shipping/handling costs.
-Available in rolls, or cut pads.
PAINT OVERSPRAY REMOVAL EFFICIENCY %
0 _ ___ __ _ ___
es ee ee eee |
dt a PAINT OVERSPRAY REMOVAL EFFICIENCY % i =|
Soave -)
5 9. – – <== fi
a | 400 500 750 2000 me
es | WEIGHT PAINT FED (grams) _
S| pees 7
ctual test report available upon request. <->
Distributed by: – yas :
eect +>
tencealen GA 5a504 a
Fitten TEL: 600.5404 AIR Bs: es:
Systems. FAX; 805-981-8675 ae
E-MAIL: sales@filtersystemsusa.com poe
WEB: wwwfiltersystemsusa.com . ae
by | Sep 27, 2025
Syetems )) PRODUCT SPECIFICATION SHEET
MODEL: PAZ2 Heavy puty Fiterstass Media
__ Weight of 22 GRAMS/SQ.FT.
__-Idea for use in a variety of crossdraft/downdraft spraybooth applications.
-99.389 f average spray removal efficiency.
__-Meets the testing and performance requirements of NESHAP 40CFR63 Subpart 6H.***
oe Anita pressure drop of .03 @ 150 FPM.
__ -Paint holding capacity of 1 LBS/SQ.FT. of media.
___ -Rated UL 900 for flammability.
Thermally stable to 212 degrees F.
E -Typically land-fillable (contains no known hazardous materials).
f -Compression rolled and packed to reduce storage and shipping/handling costs.
i -Available in rolls, or cut pads.
i
PAINT OVERSPRAY REMOVAL EFFICIENCY % oe
IN nnn oa
PAINT OVERSPRAY REMOVAL EFFICIENCY % Rie
Ba oe :
2ST ee
90
400 500 750 2000
WEIGHT PAINT FED (grams)
f
*Actual test report available upon request.
by | Sep 27, 2025
Syetems )) PRODUCT SPECIFICATION SHEET
MODEL: PAZ2 Heavy puty Fiterstass Media
__ Weight of 22 GRAMS/SQ.FT.
__-Idea for use in a variety of crossdraft/downdraft spraybooth applications.
-99.389 f average spray removal efficiency.
__-Meets the testing and performance requirements of NESHAP 40CFR63 Subpart 6H.***
oe Anita pressure drop of .03 @ 150 FPM.
__ -Paint holding capacity of 1 LBS/SQ.FT. of media.
___ -Rated UL 900 for flammability.
Thermally stable to 212 degrees F.
E -Typically land-fillable (contains no known hazardous materials).
f -Compression rolled and packed to reduce storage and shipping/handling costs.
i -Available in rolls, or cut pads.
i
PAINT OVERSPRAY REMOVAL EFFICIENCY % oe
IN nnn oa
PAINT OVERSPRAY REMOVAL EFFICIENCY % Rie
Ba oe :
2ST ee
90
400 500 750 2000
WEIGHT PAINT FED (grams)
f
*Actual test report available upon request.
by | Sep 27, 2025
THE WORLD LEADER IN CLEAN AIR SOLUTIONS
% /
FIBERGLASS PAINT ARRESTOR PADS er ) : ee
* Effectively removes paint overspray Open Weave Fiber Pattern Z (~ i a Bis sie, f
solids of all types lacquer, air dry, Holds More Paint / ae =
or baked enamel AG-28 pads are designed = & = | |
exclusively to collect paint be 2 wl | aly
* Protects exhaust ducts, fans, and overspray. They are made from is no
motors from paint buildup continuous filament glass fibers 2 ~ kas
with an open weave pattern that is vas LI
* Clean exhaust air is discharged to allows particles to penetrate deep
the atmosphere into the pad. Paint is collected throughout the full depth, extending pad life and
reducing costs. A skin backing on the air leaving side serves as a final barrier to
Economical to use prevent paint and other coatings from penetrating through the media.
Smooth Airflow Through Booth Prevents Fogging
A specially formulated thermoset resin provides high compression strength,
Lightly Loaded Air preventing AG-28 pads from collapsing and face-loading as they become
Entering Side
Close-up photo saturated. Air continues to flow smoothly through the pads, preventing
shows open weave fogging or misting of paint particles in the booth. Overspray is drawn into
pattern that allows the pads so that it does not settle on spray guns, walls, floors, or conveyors.
overspray to Proper airflow ensures healthier working conditions in conformance to
penetrate deep into
the pad. OSHA standards.
Heavily Loaded Alr Cleaner Exhaust Air Fewer Maintenance,
Entering Side Environmental Problems
ores ooedoad Continuous filament glass fibers force paint laden air to change directions
illustrates the large many times as it passes through the pad. Paint particles, unable to follow the
holding capacity of continuously weaving air stream, collect on the fibers. Cleaner exhaust air flows
each fiber. The open on through
space between 9h.
Bers continues to Maintenance problems and the hazards of fire are reduced because fans,
eri airflo
ae stows panto motors, and ducts do not accumulate layers of paint. Cleaner air is discharged
penetrate. to the atmosphere, protecting the local environment from unintentional
dusting and costly property damage.
Heavily Loaded
Groas-Section Fast, Easy Installation and Removal
Cross-section view
shows how the An entire bank of AG-28 pads can be changed in a few minutes. They fit into
aon Sized standard holding frames, with no new grids or other accessories needed.
by collecting paint AG-28 pads are directly interchangeable with other types of paint arrestors.
throughout the full Only one AG-28 pad is required per frame, including installations where two
depth, paper pads are currently used.
ADF Flondow
by | Sep 27, 2025
WINNIHt ”
i” |
ALF MTT uu | |
omoxmannexs Better Air is Our Business
AmericanAirFilter a ;
AmerSeal ae a
oe ae
Self Sealing, Internal Wire Frame Pict as 5
Ring and Link Panel Filters a
* Three models: Gold (4-ply); Blue (3-ply), Green (2-ply) 4 q 4
+ All models available with antimicrobial a9 a
* Self-sealing design provides fast and easy installation Ly 4 5
requiring no clips or latches * ig
+ Leak free, no dirty air bypass . ay 4 Le –<
* Moisture resistant, polyester media : ~~
+ MERV 8 ~
Saves on Shipping and Storage
AmerSeal self-sealing, ring and link panel filters are available The AmerSeal filter design reduces the cost of shipping and storage,
in Gold (4-ply), Blue (3-ply), and Green (2-ply) designs. when compared to conventional filters with cardboard frames. As a
AmerSeal filters offer unitized construction. Layers of AmerSeal result, using AmerSeal filters can mean fewer trips to air handlers for
filter media are sealed around the entire perimeter of the filter, maintenance personnel and smaller boxes to handle.
and at various points on the face, to bond the wire frame inside
the layers of media. The entire assembly is designed for dependable, .
trouble-free operation. Consistency of Performance
AAF's refined manufacturing processes ensure consistency of
performance for every AmerSeal filter. This consistency means
JAQ Enhanced Performance that you will have filtration you can count on each time you insert
All AmerSeal filters are available with antimicrobial. The antimicrobial a0 AmerSeal filter into your HVAC system.
is effective in restricting the spread of microbes known to affect Indoor AF is dedicated to continually improving IAQ. For more than 90 years,
Air Quality (IAQ). Used on AmerSeal filter media, the antimicrobial our slogan has been Better Air is Our Business. That experience and
helps preserve the integrity of the filter throughout its useful life by knowledge are incorporated into every AmerSeal filter you purchase.
limiting the proliferation of microbes it contacts.
Link Panels
Link panels are used primarily in side access systems where the entire
link can be easily inserted into, and removed from, the channel as
a single unit. No extended reaching or struggling with special removal
devices. Fast and simple filter changing saves maintenance cost and
time. Also, the continuous link design eliminates bypass between filters
which can allow unfiltered air to enter the system.
