POLYURETHANE FOAM | Revchem Composites

25TC300C-F_TDS.pdf

by | Sep 27, 2025

BB Dedicated w QUALITY. SERVICE, SAFETY, and INNOVATION
ENTERPRISES
4n [50-9001 Certified company
TC-300 A/B JS
RoHS
RIGID POLYURETHANE FOAM
6# DENSITY
The TC-300 A/B polyurethane foam system is a series of rigid, closed cell foams available in a variety of densities. The TC-300 can
be easily mixed by hand in small batches using a rapid, vigorous mixing action or by using a Jiffy Mixer in a drill to provide a high-
shear mix in small to large quantities. For low to high production, these foam systems can also be machine dispensed using BJB s
Centerpointe Meter-Mix equipment. Cured parts can be sanded, stapled, painted or stained within a short time after demolding. Also
available in 3#, 10#, and 16# densities.
e Easy to hand mix or machine cast Flows well into mold cavities
e Fast Demolds Excellent physical properties
PHYSICAL PROPERTIES RESULTS
Density, (free rise) Ibs/ft 6
Compressive Strength (psi) 145
Tensile Strength (psi) 160
Flexural Strength (psi) 230
Shear Strength (psi) 74
K Factor @ 77 F (25 C) 0.2
Closed Cell Content (%) 96
Water Vapor Transmission (perms/in) 1.2
HANDLING PROPERTIES (All densities) [Pata sd Part B
Mix Ratio by weight 100
Mix Ratio by volume 100
Specific Gravity @ 77 F (25 C) 1.07
Color Amber
Viscosity (cps) @77 F (25 C) Brookfield 900 1,200
Cream Time 40 50 seconds
Gel Time 2-4 minutes
Tack Free Time 3-4 minutes
Demold Time 30 45 minutes
Properties above are typical and not for specifications.
TC-300 A/B_ Page 1 of 2 Date: 05/09/2019
For more information call BJB Enterprises, Inc, (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com

25TC284B_TDS.pdf

by | Sep 27, 2025

TC-284 A/B Page 1 of 2 Date: 06/20/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com

TC-284 A/B
8-13 LB. VARIABLE RATIO, SELF-SKINNING
FLEXIBLE FOAM

TC-284 A/B is a two-component, self-skinning, flexible polyurethane foam. The cured material feels similar to an auto arm rest pad.
BJB s 6800 Series Pigments may be added to the B side for developing a wide range of colors. End users can adjust firmness with a
slight ratio change as listed below. Common applications are prototypes, bumper/crash pads, arm rests, movie special effects props and
more. Skin thickness is controlled by material/ mold temperature, and the loading of the mold.

Note: TC-284 at a ratio of 50/100 is a firm, 8 lb. density foam. At 30/100 ratio, the result will be a softer feel but the density increases
to 13 lbs. per cubic foot.

HANDLING PROPERTIES
8# DENSITY
For a Firm Feel
13# DENSITY
For a Softer yet Denser Foam
Mix Ratio (by weight)
50 parts A
100 parts B
30 Parts A
100 Parts B
Density, (free rise) lbs/ft
3
8 13
Density, (free rise) kg/m
3
128 208
Cream Time @ 77 F (25 C) 20 25 seconds 25 30 seconds
Rise Time 2 2.25 minutes 2 minutes
Demold Time @ 77 F (25 C) 30 minutes 30 minutes

Part A Part B
Specific Gravity @ 77 F (25 C) 1.15 1.04
Color Amber Off-white
Viscosity (cps) @ 77 F (25 C) Brookfield 425 1,915

*The density and processing times listed are derived from a statistical average of long-term testing. We recommend a test mix be
performed before use.

MIXING:
Mixing is best with a high speed drill or air motor with a Jiffy
Mixer . The blade shears the material and provides a thorough mix
within the 8 to 10 second period generally established for achieving
a uniform blend. Mixing too long or not enough can result in poor
material performance.
Once mixed, the material should be immediately poured. If too
much time goes by, the foam will rise in the mix container and the
batch may be lost.
When pouring the foam, avoid trying to scrape any material from
the container sidewalls or bottom. Generally, there isn t enough
time to do this and more importantly there may be material that is
not well mixed on the container sides.
POLYURETHANE FOAM SYSTEMS
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company

TC-284 A/B Page 2 of 2 Date: 06/20/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929

NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
MOLD PREPARATIONS:
The mold should be well sealed and released. Foams will seek moisture through release waxes and stick to mold surfaces if an
insufficient seal exists. Sealing can be accomplished by using acrylic or other similar sealers. The mold should be warmed to between
75- 85 F (24-29 C) prior to casting the first part. Once a mold is heated and cycled it will maintain heat for continued production.
Release systems vary in accordance to the type of mold used; however, as a general product we recommend Challenge 95 Release or a
mold release paste wax from our line of products. As a rule, silicone based releases do not work with either the flexible or rigid foam
groups of materials. The silicone migrates and often causes poor surface conditions. Silicone will also inhibit the adhesion of paints and
over-coatings. The best molds for production (rather than prototype or limited production parts) are either machined aluminum molds or
epoxy molds. Epoxy molds offer the least expensive method for long term use when cycle times allow slower heat dissipation.
DEMOLDING FOAM MATERIALS:
TC-284 A/B can be removed from the mold within a 30-minute timeframe. However, smaller masses will develop lower exothermic
reaction and may require a slightly longer cure time. It is recommended that foam parts be crushed or squeezed after demolding to
remove residual gases remaining in the cell structure. This will help to reduce post shrinkage and aid in reducing natural odors from the
foam part.
NOTE:
The B component should be gently shaken or stirred to re-blend prior to mixing with part A .
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
When first using the material, a sample should be visually inspected to be sure no crystallization is present. Crystallization of either the resin or
hardener can occur during shipment in cold weather. If the resin appears cloudy or the hardener becomes gummy, the component should be
warmed with the containers open and stirred until the material returns to its proper smooth liquid consistency.

PACKAGING Part A Part B
8-Pound Density
Free Rise*
Cubic Inches per Kit
16-Pound Density
Double Load*
Cubic Inches per Kit
Quart Kits 1 lbs. 2 lbs. 648 324
Gallon Kits 4 lbs. 8 lbs. 2,592 1,296
5-Gallon Kits 20 lbs. 40 lbs. 12,960 6,480
55-Gallon Drum Kits 225 lbs. 450 lbs. 148,800 72,900
*NOTE:
Free Rise means a foam is poured into an open mold, no top. A cubic foot of a 3-pound density will weigh 3 pounds. Double
Loading, a good starting point for closed molds is to double the amount of material used in its free rise state, this helps to capture the
parts detail and create a more resilient skin. Our cured samples represent double loading.
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact on the
skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles when handling
this product.
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended to
remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.

Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including Diethanolamine and Ethylene glycol, which are known to the State
of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Scan QR code to see our How-to Foam
Video

25TC296-F_TDS.pdf

by | Sep 27, 2025

BB Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
ENTERPRISES
Au 1SO-9001 Certified company
FIRE RETARDANT FLEXIBLE FOAM RoHS
6 LB DENSITY
TC-296 FR A/B is a 6 Ib. medium density, water blown flexible foam with fire retardant properties. This product was developed due to
ongoing demand for fire retardant foams in the industries of Movie Special Effects, Theme Parks, Haunted Houses, and Theatrical
Performance. Firmness of the foam can be controlled by mold temperature and the amount loaded in the mold. BJB s 6800 Series
Pigments may be added to the B side for developing a wide range of colors. TC-296 FR A/B can be hand mixed, machine
dispensed, or mixed with a Jiffy Mixer .
Prototypes Medical training devices
Prosthetics * Movie props/ Special effects
MEETS THE FOLLOWING:
D.O.T. Flammability of Interior Materials – FMVSS 302
HANDLING PROPERTIES | PatA si Part B
Mix Ratio by weight a 100
Specific Gravity @ 77 F (25 C) 1.188 1.054
Color Pale Yellow Off White
Viscosity (cps) @ 77 F (25 C) Brookfield 1500
Density, (free rise) Ibs/ft 6
Density, (free rise) kg/m? 96.1
Cream Time 20 25 seconds
Rise Time 1.25 1.5 minutes
Tack Free Time 6 7 minutes
Demold Time 20 30 minutes
Properties above are typical and not for specifications,
*The density and processing times listed are derived from a statistical average of long-term testing. We recommend a test mix be
performed before use. BJB quality control tests and product packaging are based on the 50/100 pbw ratio.
i Mixing is best with a high speed drill or air motor with a Jiffy Mixer .
Ee eRe Ly 10-12K 9 9-10X ee The blade shears the material and provides a thorough mix within the 8
) iy CNSR somal to 10 second period generally established for achieving a uniform blend.
Bl sae: , Mixing too long or not enough can result in poor material performance.
3Ib 4lb 6b Bib Once mixed, the material should be immediately poured. If too much
eel | time goes by, the foam will rise in the mix container and the batch may
sj be lost.

a When pouring the foam, avoid trying to scrape any material from the
fees A eae container sidewalls or bottom. Generally, there isn t enough time to do
_ Polysoftt polysott TC-296 FR ee this and more importantly there may be material that is not well mixed
Hite pice on the container sides.

TC-296 FR A/B_ Page 1 of 2 Date: 11/28/2018
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www. bjbenterprises.com

25TC284BLF_TDS.pdf