by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
fF = CA 92647 USA
INTERNATIONAL INC.
Data Sheet TOOLWRIGHT 3 & 5
High Elongation Release Film coated with adhesive
lM DESCRIPTION
Toolwright series is an extruded release film coated with a pressure sensitive adhesive. Toolwright 3 has a thinner film
than Toolwright 5 and can be more easily applied over complex contour surfaces. Provides excellent release from all
common resin systems for multiple releases. Toolwright 3 has high elongation, good tear strength, high temperature
resistance and excellent clean up after removal.
M@ BENEFITS
+ High elongation allows for easier covering of complex surfaces, improving part surface quality.
+ Good adhesion to metal, composite, Tooling block and rubber tooling for longer service life.
+ Tougher film is more tear resistant and so it s easier to stretch over complex shapes without damage.
+ Extend the life of worn tools avoiding cost of new tools.
@ TECHNICAL DATA
Toolwright 3 Toolwright 5
Maximum use temperature 260 C (500 F) 260 C (500 F)
Carrier type Extruded fluoropolymer Extruded fluoropolymer
Adhesive type Silicone Silicone
Elongation at break 350% 350%
Colour Light orange Light orange
Total thickness 75 jum (0.003 inch) 125 ym (0.005 inch)
Film thickness 50 um (0.002 inch) 100 yum (0.004 inch)
Adhesive thickness 25 um (0.001 inch) 25 um (0.001 inch)
Shelf life 18 months from date of shipment when stored in the
original packaging at 22 C (72 F)
@ SIZES
Toolwright 3 Toolwright 5
127 cm – 16.5 m (50 inches – 18 yards) 117 cm – 16.5 m (46 inches – 18 yards)
+ Other widths available, please contact Airtech for more information.
SUSTAINABILITY
CC a) canbe <4 Recyclable
-used packaging
re-use VP
@ NOTES
+ Toolwright 3R & Toolwright 5R also available with rubber adhesive, allowing Toolwright to be used
without risk of silicone contamination such as moulding off parts for reverse tool manufacture.
+ Toolwright should be applied by carefully lifting the edge of the backing, then applying the adhesive
side to the mould surface. The remainder of backing should then be carefully removed while pressing
the Toolwright onto the mould surface with an Airsweep or other straight edge. A vacuum bag can then
be applied to remove any residual air. A cure cycle under vacuum will provide the best results.
+ The maximum use temperature is dependent upon the duration at maximum temperature and is
process specific, Airtech recommends testing prior to use.
Last updated : 2025-02-07
Catalog position : Pressure sensitive tapes
ste contin creo ue nding sarge eyed ot conta itech trator doe tse pony for the pevomnance fh mae for ry arr. The mates sols Artech inteton n
by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
y a lan Huntington Beach Fax: +1 714-899-8179 Website : www.airtech.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet TOOLTEC CS5
High elongation PTFE film coated with silicone adhesive
DESCRIPTION
Tooltec CSS is a PTFE film coated with a high temperature silicone pressure sensitive adhesive. It can be used
to seal masters and leaky tool surfaces while providing semi-permanent and contamination free part release.
Tooltec CS5 is a non-reinforced mold surface reconditioning tape allowing conformance to complex contours
and providing a semi-permanent release for contoured shapes.
@ BENEFITS
+ Provides semi-permanent release saving time spent cleaning tooling and reapplying release agents.
+ Good elongation, so complex tools can be reconditioned and master models finished for molding.
+ Improve tool surface finish and aid resin flow for better part surface finish and reduced hand finishing.
@ TECHNICAL DATA
Maximum use temperature 500 F (260 C)
Carrier type PTFE
Adhesive type Silicone
Color Light brown
Total thickness 0.0065 inch (165 um)
Film thickness 0.005 inch (127 pm)
Adhesive thickness 0.0015 inch (38 pm)
Elongation at break 300 %
Shelf life 18 months from date of shipment when
stored in original packaging at 72 F (22 C)
COMMONLY USED SIZES
36 inches (91 cm) 18 yards (16.5 m)
48 inches (122 cm) 18 yards (16.5 m)
+ Other sizes available on special order.
@ NOTES
+ Tooltec CS5 should be applied by carefully lifting the edge of the backing, then applying the adhesive
side to the mold surface. The remainder of backing should then be carefully removed while pressing the
Tooltec CS5 onto the mold surface with an Airsweep or other straight edge. A vacuum bag can then be
applied to remove any residual air. A cure cycle under vacuum will provide the best results.
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
Last updated : 2019-10-07
Catalog position : Pressure sensitive tapes 7
the conditions or methods fuse Inching storage, ae beyond out contol Artech Intemational does not ese ay regan othe performance of material fo any para we Te mate soda
Artech Iematonal ic decals and bye wanes any anda pled varates nung witout tain the mpd waranles of mertantablty nd of fnes fo partcar use. he nfermaton contained heen
presents ypcal properter and shold not be uted fr speciation purpose Any tandton pred for your convenience ony The ofl language sEngish andthe ofl wie alors USA
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
f Si CA92647 USA
INTERNATIONAL INC.
Data Sheet TOOLTEC A005, A007 & A012
Reinforced PTFE coated fibreglass with silicone adhesive
lM DESCRIPTION
Tooltec pressure sensitive tapes are designed to adhere to tool surfaces providing semi-permanent release and a
reconditioned surface. It can be used on all types of moulds, press platens, caul sheets or any surface that comes in
contact with resins or adhesives. Release agents are not required on the mould surface thereby reducing cost and
parts contamination. Tooltec are reinforced mould surface reconditioning tapes providing a semi-permanent release
for flat tools. These products come standard with a silicone pressure adhesive, but can also be supplied with an acrylic
adhesive by special order.
@ BENEFITS
+ Provide semi-permanent release saving time spent cleaning tooling and reapplying release agents.
+ Can be used to recondition worn or damaged tools for extended service, avoiding cost of remanufacture.
+ Improve tool surface finish and aid resin flow for better part surface finish and reduced hand finishing.
@ TECHNICAL DATA
Tooltec A005 Tooltec A007 Tooltec A012
Maximum use temperature 260 C (500 F) 260 C (500 F) 260 C (500 F)
Carrier type PTFE/ Glass PTFE/ Glass PTFE/ Glass
Adhesive type Silicone Silicone Silicone
Colour Light brown Light brown Light brown
Total thickness 125 ym (0.005 inch) 175 ym (0.007 inch) 304 um (0.012 inch)
Film thickness 75 ym (0.003 inch) 125 yum (0.005 inch) 254 um (0.010 inch)
Adhesive thickness 50 um (0.002 inch) 50 um (0.002 inch) 50 um (0.002 inch)
Shelf life 18 months from date of shipment when stored in
original packaging at 22 C (72 F)
@ SIZES
Tooltec A005 Tooltec A007 Tooltec A012
2.54 cm – 33 m (1″ – 36 yards) 2.54 cm – 33 m (1″- 36 yards) –
5.08 cm – 33 m (2″ – 36 yards) 5.08 cm – 33 m (2″ – 36 yards) –
91 cm – 16.5 m (36″- 18 yards) 91 cm – 16.5 m (36″ – 18 yards) 91 cm – 16.5 m (36″ – 18 yards)
122 cm – 16.5 m (48″ – 18 yards) 122 cm – 16.5 m (48″ – 18 yards) –
+ Other sizes available on special order.
SUSTAINABILITY
CC a) canbe <4 Recyclable
-used packaging
re-use VP
@ NOTES
+ Tooltec should be applied by carefully lifting the edge of the backing, then applying the adhesive side
to the mould surface. The remainder of backing should then be carefully removed while pressing the
Tooltec onto the mould surface with an Airsweep or other straight edge. A vacuum bag can then be
applied to remove any residual air. A cure cycle under vacuum will provide the best results.
+ Colour variations are due to sizing and sintering process and have no relationship to % of PTFE content.
+ The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
Last updated : 2025-02-07
Catalog position : Pressure sensitive tapes
ste contin creo ue nding sarge eyed ot conta itech trator doe tse pony for the pevomnance fh mae for ry arr. The mates sols Artech inteton n
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
f Si CA92647 USA
INTERNATIONAL INC.
Data Sheet TOOLTEC A005, A007 & A012
Reinforced PTFE coated fibreglass with silicone adhesive
lM DESCRIPTION
Tooltec pressure sensitive tapes are designed to adhere to tool surfaces providing semi-permanent release and a
reconditioned surface. It can be used on all types of moulds, press platens, caul sheets or any surface that comes in
contact with resins or adhesives. Release agents are not required on the mould surface thereby reducing cost and
parts contamination. Tooltec are reinforced mould surface reconditioning tapes providing a semi-permanent release
for flat tools. These products come standard with a silicone pressure adhesive, but can also be supplied with an acrylic
adhesive by special order.
@ BENEFITS
+ Provide semi-permanent release saving time spent cleaning tooling and reapplying release agents.
+ Can be used to recondition worn or damaged tools for extended service, avoiding cost of remanufacture.
+ Improve tool surface finish and aid resin flow for better part surface finish and reduced hand finishing.
@ TECHNICAL DATA
Tooltec A005 Tooltec A007 Tooltec A012
Maximum use temperature 260 C (500 F) 260 C (500 F) 260 C (500 F)
Carrier type PTFE/ Glass PTFE/ Glass PTFE/ Glass
Adhesive type Silicone Silicone Silicone
Colour Light brown Light brown Light brown
Total thickness 125 ym (0.005 inch) 175 ym (0.007 inch) 304 um (0.012 inch)
Film thickness 75 ym (0.003 inch) 125 yum (0.005 inch) 254 um (0.010 inch)
Adhesive thickness 50 um (0.002 inch) 50 um (0.002 inch) 50 um (0.002 inch)
Shelf life 18 months from date of shipment when stored in
original packaging at 22 C (72 F)
@ SIZES
Tooltec A005 Tooltec A007 Tooltec A012
2.54 cm – 33 m (1″ – 36 yards) 2.54 cm – 33 m (1″- 36 yards) –
5.08 cm – 33 m (2″ – 36 yards) 5.08 cm – 33 m (2″ – 36 yards) –
91 cm – 16.5 m (36″- 18 yards) 91 cm – 16.5 m (36″ – 18 yards) 91 cm – 16.5 m (36″ – 18 yards)
122 cm – 16.5 m (48″ – 18 yards) 122 cm – 16.5 m (48″ – 18 yards) –
+ Other sizes available on special order.
SUSTAINABILITY
CC a) canbe <4 Recyclable
-used packaging
re-use VP
@ NOTES
+ Tooltec should be applied by carefully lifting the edge of the backing, then applying the adhesive side
to the mould surface. The remainder of backing should then be carefully removed while pressing the
Tooltec onto the mould surface with an Airsweep or other straight edge. A vacuum bag can then be
applied to remove any residual air. A cure cycle under vacuum will provide the best results.
+ Colour variations are due to sizing and sintering process and have no relationship to % of PTFE content.
+ The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
Last updated : 2025-02-07
Catalog position : Pressure sensitive tapes
ste contin creo ue nding sarge eyed ot conta itech trator doe tse pony for the pevomnance fh mae for ry arr. The mates sols Artech inteton n
by | Sep 27, 2025
Resin infusion products
Toolfusion 3A/ 3B
High temperature infusion resin with low initial cure temperature
Toolfusion 3A/ 3B is a two part low viscosity epoxy infusion resin formulated to produce pre-preg quality, composite molds. Toolfusion 3A/ 3B
has a low initial cure temperature of 120 F (49 C) and can be post cured to achieve a high glass transition temperature of 425 F (218 C). Void
contents of less than 1% are achievable. Toolfusion 3A/ 3B will work in various RTM and VARTM processes including single and double bag
arrangements to produce autoclave quality laminates.
Resin infusion process delivers very high quality laminates with low manufacturing costs, no refrigeration
costs, no autoclave running costs.
Low initial cure temperature for low thermal expansion e ect during curing and ability to use low cost master
model materials.
Nano technology delivers outstanding toughness & high Tg. (425 F or 218 C) for long tool life and reduced life
cycle cost.
Low viscosity allows infusion of thicker and more complex laminates with fewer resin feed lines.
In comparison to metallic tools, Toolfusion 3A /3B composite tools are lighter weight for easier
manual handing.
In comparison to metallic tooling, Toolfusion 3A/ 3B composite tools have faster heat up and cool down
rates for reduced production costs.
Toolfusion 3A/ 3B composite tooling laminates have vacuum integrity for vacuum bag processing of parts in
oven and autoclave.
Test method
Material type Epoxy
Color Black : Clear (A : B)
Mix ratio by weight 100 : 85 (A : B)
Pot life 300 minutes (100 g at 72 F or 22 C)
DESCRIPTION
BENEFITS
TECHNICAL DATA
Viscosity (initial at 72 F or 22 C) 450 cps
Density (mixed) 1.13 g/cm
Glass transition temperature 425 F (218 C)
Hardness 89 Barcol ASTM D2583
Shrinkage 0.9%
Shelf life 12 months from date of shipment when stored in
original packaging at 72 F (22 C)
Packaging Part A Packaging Part B Weight Part A Weight Part B
5 gallons 5 gallons 45 lbs (20.4 kg) 40 lbs (18.1 kg)
Initial cure:
Cure laminate on master model with full vacuum applied.
Raise temperature to 120 F (49 C) and hold for 12 hours.
Remove vacuum bagging materials and attach back-up structure if required.
Carefully remove the laminate continue with post cure.
Post cure schedule:
Ramp to 150 F (65 C) and hold for 60 minutes.
Ramp to 200 F (93 C) and hold for 60 minutes.
Ramp to 250 F (121 C) and hold for 60 minutes.
Ramp to 300 F (149 C) and hold for 60 minutes.
Ramp to 350 F (177 C) and hold for 60 minutes.
Ramp to 400 F (204 C) and hold for 120 minutes.
3
SIZES
CURING DATA
Last updated : 2020-08-26
Print this page Download this page Print SDS Download SDS
As the conditions or methods of use, including storage, are beyond our control, Airtech International, Inc. does not assume responsibility for the performance
of this material for any particular use. The material is sold “as is”. Airtech International, Inc. disclaims, and buyer waives, any and all implied warranties,
including without limitation the implied warranties of merchantability and of tness for particular use. The information contained herein represents typical
properties and should not be used for speci cation purposes. Any translation is provided for your convenience only. The o cial language is English and the
o cial law is California, USA.
Part A and Part B are sold separately.
NOTES
previous next
by | Sep 27, 2025
Resin infusion products
Toolfusion 3A/ 3B
High temperature infusion resin with low initial cure temperature
Toolfusion 3A/ 3B is a two part low viscosity epoxy infusion resin formulated to produce pre-preg quality, composite molds. Toolfusion 3A/ 3B
has a low initial cure temperature of 120 F (49 C) and can be post cured to achieve a high glass transition temperature of 425 F (218 C). Void
contents of less than 1% are achievable. Toolfusion 3A/ 3B will work in various RTM and VARTM processes including single and double bag
arrangements to produce autoclave quality laminates.
Resin infusion process delivers very high quality laminates with low manufacturing costs, no refrigeration
costs, no autoclave running costs.
Low initial cure temperature for low thermal expansion e ect during curing and ability to use low cost master
model materials.
Nano technology delivers outstanding toughness & high Tg. (425 F or 218 C) for long tool life and reduced life
cycle cost.
Low viscosity allows infusion of thicker and more complex laminates with fewer resin feed lines.
In comparison to metallic tools, Toolfusion 3A /3B composite tools are lighter weight for easier
manual handing.
In comparison to metallic tooling, Toolfusion 3A/ 3B composite tools have faster heat up and cool down
rates for reduced production costs.
Toolfusion 3A/ 3B composite tooling laminates have vacuum integrity for vacuum bag processing of parts in
oven and autoclave.
Test method
Material type Epoxy
Color Black : Clear (A : B)
Mix ratio by weight 100 : 85 (A : B)
Pot life 300 minutes (100 g at 72 F or 22 C)
DESCRIPTION
BENEFITS
TECHNICAL DATA
Viscosity (initial at 72 F or 22 C) 450 cps
Density (mixed) 1.13 g/cm
Glass transition temperature 425 F (218 C)
Hardness 89 Barcol ASTM D2583
Shrinkage 0.9%
Shelf life 12 months from date of shipment when stored in
original packaging at 72 F (22 C)
Packaging Part A Packaging Part B Weight Part A Weight Part B
5 gallons 5 gallons 45 lbs (20.4 kg) 40 lbs (18.1 kg)
Initial cure:
Cure laminate on master model with full vacuum applied.
Raise temperature to 120 F (49 C) and hold for 12 hours.
Remove vacuum bagging materials and attach back-up structure if required.
Carefully remove the laminate continue with post cure.
Post cure schedule:
Ramp to 150 F (65 C) and hold for 60 minutes.
Ramp to 200 F (93 C) and hold for 60 minutes.
Ramp to 250 F (121 C) and hold for 60 minutes.
Ramp to 300 F (149 C) and hold for 60 minutes.
Ramp to 350 F (177 C) and hold for 60 minutes.
Ramp to 400 F (204 C) and hold for 120 minutes.
3
SIZES
CURING DATA
Last updated : 2020-08-26
Print this page Download this page Print SDS Download SDS
As the conditions or methods of use, including storage, are beyond our control, Airtech International, Inc. does not assume responsibility for the performance
of this material for any particular use. The material is sold “as is”. Airtech International, Inc. disclaims, and buyer waives, any and all implied warranties,
including without limitation the implied warranties of merchantability and of tness for particular use. The information contained herein represents typical
properties and should not be used for speci cation purposes. Any translation is provided for your convenience only. The o cial language is English and the
o cial law is California, USA.
Part A and Part B are sold separately.
NOTES
previous next
by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtechintl.com
y a lan Huntington Beach Fax: +1 714-899-8179 Website : www.airtechonline.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet TEFLEASE MG2
High temperature PTFE pressure sensitive tape
DESCRIPTION
Teflease MG2 is a PTFE film coated with a silicone adhesive. Teflease MG tapes will release from most resin
systems. They are ideal for use on tooling blocks and all areas where high elongation and release is needed.
Teflease MG tapes will form to critical contours and mold surfaces while offering multiple releases or may be
used to cover multiple detail mold seams. They provide a semi-permanent release on cured Airpad tooling
rubber and Aircast 3700 pressure intensifiers and mandrels.
@ BENEFITS
+ Provides semi-permanent release and superior surface finish, saving time and improving quality.
+ Protect rubber tooling mandrels and intensifiers from resin attack, extending tool life and reducing cost.
+ Good elongation makes application to complex shapes easier, reducing time and improving quality.
@ TECHNICAL DATA
Maximum use temperature 500 F (260 C)
Carrier type PTFE
Adhesive type Silicone
Color Light brown
Total thickness 0.0035 inch (88 1m)
Film thickness 0.002 inch (50 jum)
Adhesive thickness 0.0015 inch (38 pm)
Elongation at break 125 %
Shelf life 18 months from date of shipment when
stored in original packaging at 72 F (22 C)
COMMONLY USED SIZES
1 inch (2.54 cm) 36 yards (33 m) 60 rolls per case
2 inches (5.08 cm) 36 yards (33 m) 30 rolls per case
+ Broken cases and other widths available on special order.
+ Other thickness available:
MG3 – 0.0045 inch (115 tm) total thickness
MG5 – 0.0065 inch (165 tm) total thickness
@ NOTES
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
Last updated : 2019-10-07
Catalog position : Pressure sensitive tapes
-Asthecondton or methods fuse, lncluing storage ae beyond our control Altech tration nc does ot sume any espns fe the performance of his material for any parca ue. The mater sld”s
Artech eration ne dclsne and buyer waive, any analimpled warantesincidg without mtn the pled warns of merchant and of ness fo pata use. The formation contaned heen
teptesents ypc properties and should nat be used for specication purposes Any tnsstio provide or yout convenience ony The afi anguages English andthe ofa law Calf, USA
by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtechintl.com
y a lan Huntington Beach Fax: +1 714-899-8179 Website : www.airtechonline.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet TEFLEASE MG2
High temperature PTFE pressure sensitive tape
DESCRIPTION
Teflease MG2 is a PTFE film coated with a silicone adhesive. Teflease MG tapes will release from most resin
systems. They are ideal for use on tooling blocks and all areas where high elongation and release is needed.
Teflease MG tapes will form to critical contours and mold surfaces while offering multiple releases or may be
used to cover multiple detail mold seams. They provide a semi-permanent release on cured Airpad tooling
rubber and Aircast 3700 pressure intensifiers and mandrels.
@ BENEFITS
+ Provides semi-permanent release and superior surface finish, saving time and improving quality.
+ Protect rubber tooling mandrels and intensifiers from resin attack, extending tool life and reducing cost.
+ Good elongation makes application to complex shapes easier, reducing time and improving quality.
@ TECHNICAL DATA
Maximum use temperature 500 F (260 C)
Carrier type PTFE
Adhesive type Silicone
Color Light brown
Total thickness 0.0035 inch (88 1m)
Film thickness 0.002 inch (50 jum)
Adhesive thickness 0.0015 inch (38 pm)
Elongation at break 125 %
Shelf life 18 months from date of shipment when
stored in original packaging at 72 F (22 C)
COMMONLY USED SIZES
1 inch (2.54 cm) 36 yards (33 m) 60 rolls per case
2 inches (5.08 cm) 36 yards (33 m) 30 rolls per case
+ Broken cases and other widths available on special order.
+ Other thickness available:
MG3 – 0.0045 inch (115 tm) total thickness
MG5 – 0.0065 inch (165 tm) total thickness
@ NOTES
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
Last updated : 2019-10-07
Catalog position : Pressure sensitive tapes
-Asthecondton or methods fuse, lncluing storage ae beyond our control Altech tration nc does ot sume any espns fe the performance of his material for any parca ue. The mater sld”s
Artech eration ne dclsne and buyer waive, any analimpled warantesincidg without mtn the pled warns of merchant and of ness fo pata use. The formation contaned heen
teptesents ypc properties and should nat be used for specication purposes Any tnsstio provide or yout convenience ony The afi anguages English andthe ofa law Calf, USA
by | Sep 27, 2025
SikaLastomer
-95 1 / 2
Product Data Sheet
Version 8/25/08
SikaLastomer
-95
Isobutylene Tripolymer Tape
Technical Product Data (typical values)
Chemical base
Butyl
Color Gray
Specific Gravity (ASTM D 792) 1.44 to 1.56
Total solids (ASTM C 771) 100%
Penetration (ASTM D 217) cone at 77 F / 300 gr. 70 to 90 (7.0 9.0 mm)
Flexibility (AAMA 800-92) (ASTM C 734) No cracking or loss of adhesion at -60 F (-51 C)
Elongation
1
(ASTM C 908) 1100% min
Staining (ASTM D 925) Will not stain painted or unpainted surfaces
Vehicle bleed out (ASTM C 771) 158 F (70 C) for 21 days
No exudation of vehicle on Whatman No. 40 filter
paper
Crazing to acrylic plastics Will not craze plastics
Application temperature product -5 F to 120 F (-20 C to 49 C)
Tensile adhesive strength
1
(ASTM C 907) 17 to 20 psi min (cohesive failure)
Peel adhesion (ASTM D 3330 modified 90 peel) 8 lbs/in. min (cohesive failure)
Corrosivity
No darkening, etching or salt deposits on
GALVALUME
, KYNAR 500
, ZINCALUME
,
aluminum, aluminized steel or galvanized metal
Weatherability (ASTM G 53) (1000 h exposure)
No cracking, bleeding or loss of rubbery
characteristics
Static water head test (MBMA ice damming)
Sealant passes 8 in. water head in an erected
interlocked panel joint
Service temperature
permanent
-60 F to 212 F (-51 C to 100 C)
Shelf life (storage below 80 F (27 C)) 18 months
1)
77 F (25 C)
Description
SikaLastomer
-95 Isobutylene
Tripolymer Tape is a high performance,
tacky elastic butyl tape which is designed
to bond through oily GALVALUME
,
KYNAR 500
, aluminized steel,
ZINCALUME
, galvanized metal,
aluminum, siliconized polyester and
polyvinyl fluoride painted metals, glass,
wood, concrete, fiber-reinforced plastics
(FRP) and similar substrates. Its superior
surface tack affords tenacious adhesion
to these substrates without pre-wiping
the surface even at temperatures as low
as 5
o
F. Where superior tensile strength
and extensibility (webbing/elongation)
are critical, in both hot and cold climates,
use SikaLastomer Isobutylene
Tripolymer Tape rather than general
purpose butyl tapes. SikaLastomer is
formulated without asbestos fillers.
SikaLastomer
-95 contains a special
additive which inhibits a broad spectrum
of microbial activity. SikaLastomer
-95
is manufactured in accordance with ISO
9001 / 14001 quality assurance system
and the responsible care program.
Product Benefits
– Resistance to fungus / Mildew growth
– Almost odorless
– Paintable
– Will not stain painted or unpainted
surfaces
Areas of Application
Specifically developed for sealing critical
Standing Seam Roof (SSR) endlaps and
lap joints for metal building roofs,
skylights, roof curbs, smoke vents, air
conditioning equipment, curtain wall
joints and perimeter areas around
windows and doors. Sealing exterior lap
joints of grain storage bins and sealing
the base to the concrete pad. Designed
for sealing polyethylene sheeting and
metal sewer pipes. Sealing exposed,
concealed exterior lap joints of
aluminum, steel, coated metals, wood,
roof rails and door hinges in transport
equipment. Waterproofs rivet seams and
lap seams in truck trailers and RVs.
SikaLastomer
-95 2 / 2
Sika Corporation
Industry Division
30800 Stephenson Highway
Madison Heights, MI 48071
USA
Tel. 248 577 0020
Fax 248 577 0810
Further information available at:
www.sikaindustry.com
Excellent for sealing between dissimilar
metals to prevent electrolysis.
This product is suitable for experienced
professional users only. Tests with actual
substrates and conditions have to be
performed to ensure adhesion and
material compatibility.
Chemical Resistance
Excellent resistance to water, water
vapor, ozone and alcohols. Fair to good
resistance to weak acids and bases
(including silage juice). Poor resistance
to aliphatic, aromatic and keytone
solvents and oils. The above information
is offered for general guidance only.
Advice on specific applications will be
given on request.
Method of Application
Surface preparation
Advice on specific applications is
available from the Technical Service
Department of Sika Industry.
Removal
SikaLastomer
-95 may be removed from
tools and equipment with mineral spirit or
another suitable solvent.
Following use wash hands with soap and
water. Do not use solvents on hands!
Meets following qualifications
MIL-C-18969B, Type II, Class B
TT-C-1796A, Type II, Class B
AAMA 804-92 and AAMA 807-92
FDA for packaging and transporting
food as listed in CFR Title 21
USDA Approved for incidental food
contact
Freight class.: Caulking Compound,
NOIBN, NMFC #149610, Class 55
HMIS
Health 0
Flammability 1
Reactivity 0
Personal Protection A
Further Information
Copies of the following publications are
available on our website
www.sikaindustry.com:
-Material Safety Data Sheets
-Product Data Sheet
-Sika Primer Chart
-General guidelines for bonding and
sealing with Sika products
In case of emergency call:
Chemtrec: 800-424-9300
International: 703-527-3887
For further information and advice
regarding transportation, handling,
storage and disposal of chemical
products, users should refer to the actual
Material Safety Data Sheets containing
physical, ecological, toxicological and
other safety related data. It is highly
recommended to read the actual Material
Safety Data Sheet before using the
product.
-KEEP OUT OF REACH OF CHILDREN
-NOT FOR INTERNAL CONSUMPTION
-FOR INDUSTRIAL USE ONLY
Packaging Information
Rolls Multiple sizes
Endlap pads Multiple sizes
Value Basis
All technical data stated on this Product
Data Sheet are based on the results of
laboratory tests only. Actual measured
data in the field may vary due to site
specific conditions which are not known
to Sika and beyond our control.
Clean Up
Dispose of in accordance with current,
applicable local, state and federal
regulations.
Limited Material Warranty
SIKA warrants this product for one year
from date of installation to be free from
manufacturing defects and to meet the
technical properties on the current
Product Data Sheet if used as directed
within shelf life. User determines
suitability of product for intended use and
assumes all risks. Buyer s sole remedy
shall be limited to the purchase price or
replacement of product exclusive of labor
or cost of labor. NO OTHER
WARRANTIES IMPLIED OR EXPRESS
SHALL APPLY INCLUDING ANY
WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE. SIKA SHALL NOT BE
LIABLE UNDER ANY LEGAL THEORY
FOR SPECIAL OR CONSEQUENTIAL
DAMAGES. SIKA SHALL NOT BE
RESPONSIBLE FOR THE USE OF
THIS PRODUCT IN A MANNER TO
INFRINGE ON ANY PATENT OR ANY
OTHER INTELLECTUAL PROPERTY
RIGHTS HELD BY OTHERS.
Legal Notes/Disclaimer
All information provided by Sika
Corporation ( Sika ) concerning Sika
products, including but not limited to, any
recommendations and advice relating to
the application and use of Sika products,
is given in good faith based on Sika s
current experience and knowledge of its
products when properly stored, handled
and applied under normal conditions in
accordance with Sika s instructions. In
practice, the differences in materials,
substrates, storage and handling
conditions, actual site conditions and
other factors outside of Sika s control are
such that Sika assumes no liability for
the provision of such information, advice,
recommendations or instructions related
to its products, nor shall any legal
relationship be created by or arise from
the provision of such information, advice,
recommendations or instructions related
to its products. The user of the Sika
product(s) must test the product(s) for
suitability for the intended application
and purpose before proceeding with the
full application of the product(s).
Sika reserves the right to change the
properties of its products without notice.
All sales of Sika product(s) are subject to
its current terms and conditions of sale
which are available at www.sikacorp.com
or by calling 201-933-8800.
Prior to each use of any Sika product,
the user must always read and follow the
warnings and instructions on the
product s most current Product Data
Sheet, product label and Material Safety
Data Sheet which are available at
www.sikaindustry.com. Nothing
contained in any Sika materials relieves
the user of the obligation to read and
follow the warnings and instruction for
each Sika product as set forth in the
current Product Data Sheet, product
label and Material Safety Data Sheet
prior to product use.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
STRETCH- VAC 2000
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
Soft, co-extruded, ultra high elongation, multi layered
film, produced from a modified polyamide resin.
Easily conformable for complex contoured parts,
formulated to be less affected by environmental
changes and remains flexible in low humidity
conditions.
Recommended as a bagging film for advanced
composite fabrication, when a dependable,
conformable, soft, stretchable bag is required.
Fewer pleats are needed when vacuum bagging
either complex or simple contoured parts, due to its
unique characteristics.
Manufactured using advanced state-of-the-art
blown film technology.
Can be heat seamed to meet any custom shape
requirements.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Red and transparent
Tensile strength at break (ASTM D882) 103.42 MPa 15000 PSI
Elongation at break (ASTM D882) 400%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45Kg Up to 100lb
Widths Up to 4.06m (open) Up to 160in (open)
Formats available Lay-flat tube, sheet, V sheet
STORAGE
Stretch-Vac 2000 is hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use
is therefore an important factor for successful performance. The higher the moisture content the more flexible they become.
Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
