372710_TDS.pdf

a ee ~
ne 2 |
@ Chem | ae Me
ma Sa . a 4 |
cane cane em ia
. Release Innovation i ” 4.” mS oa aa ab f
: PRODUCT DATA SHEET. }
Chemlease 2710 ae
Semi-Permanent Release Agent |
( 2016 Chom-Trend LP,
Description 2. Use an HVLP spray gun to apply a light, even coat to the
Chemlease 2710 is a HAPs-free* solvent-based semi-permanent mold surface. As a guide to achieving a “light coat” when the
releasant for the composites industry which affords easy film is applied to a VERTICAL mold surface, the wet film
application In one step. The product should be applied to the mold should shine, but there should be no runs in it. Runs in the
surface very lightly and allowed to dry. The original mold surface film indicate too heavy an application (see above.)
finish appearance will be reproduced once the product is dry. 3, Keep the spray gun 8-10 inches away from the mold surface
* HAPs are not formula constituents of this product. Standard while spraying approximately two linear feet (0.6 meter) per
manufacturing processes may result in trace quantities [<0 .1%] of second. We recommend 7-10 psi for the fluid pressure and HAPs. 20-30 psi for the air pressure as a general guideline. 4, Apply 5 coats one after another. No waiting between coats is Application ~ Wipe-On Method necessary. For a new mold or difficult to release part, apply 1, The mold surface must be cleaned to remove all traces of wax, an additional 2 coats for a total of 7 coats. release agents, and other sealers before application of 5. After last coat is applied, allow 30 minutes for cure before gel Chemlease 2710 can be attempted. Use the appropriate coating. Begin molding. Chemlease Mold Cleaner (Contact your Chemlease Sales 6. When release becomes difficult reapply 1 coat of Representative for a recommendation). Chemlease 2710. Allow to cure for 15 minutes and resume 2. Apply a light, even coat to the mold surface. As a guide to molding. achieving a "light coat" when the film is applied to a VERTICAL Important mold surface, the wet film should shine, but there should be no The recommended number of coats and cure times are a general runs in it. In normal temperature conditions, the film should guideline found to be more than sufficient in a broad spectrum of evaporate less than 60 seconds after applying. If the film still molding conditions. When molding products with extreme remains after 1 minute, the product was applied too heavily and geometries or experiencing low-humidity conditions in the shop, will produce streaks on the mold, To fix the affected area, wipe the customer may find the need to extend the cure time between off the remaining film. Then wipe a lighter coat with a Coats and increase the number of coats applied to the mold. The dampened sealer cloth and immediately wipe off to remove the efficiency of a release film is best determined through a streaks. Then recoat as described above, combination of tape tests and experimentation. 3, As soon as the wiping action appears not to be forming a film, add more product to the cloth as describe above in step #2. Storage 4. Continue working across the moid until Its entire surface has Do not store at temperatures above 49 C/120 F. Keep container been coated. tightly sealed to prevent evaporation and/or contamination. If 5. Allow the film to dry for 15 minutes, stored In cold temperatures allow warming to room temperature 6. Using the same procedure, apply 5 complete coats. For anew before using. mold or difficult to release part, apply an additional 2 coats for a total of 7 coats, Packaging 7. Cure for a minimum of 30 minutes after the final coat has been Chemlease 2710 is available in a variety of package sizes. applied, Please contact Chem-Trend customer service for details. 8. Begin molding and continue until release-ease appears tight. 9. When release becomes difficult reapply 1 coat of Safety Data Chemlease 2710, Allow to cure for 15 minutes and resume Safety Data Sheets are available for ail Chemlease products and molding. should be consulted prior to use of the product. Application -- Spray-On Method % Z 5 z . 1, The mold surface must be cleaned to remove all traces of a Sauces eens 2 wax, release agents, and other sealers before the application PLsuesis lointiteinatnavay apie ncerin tact ore of Chemlease 2710 can be attempted. Use the appropriate SI eee OU a a EID NG tt Tabs Chemlease Mold Cleaner (Contact your Chemlease Sales a ON RS oe eee Representative for a recommendation). Hh SSC RE aL oa mura alee a Peet a see ae While the technical information and suggestions for use contained herein are believed to be accurate and reliable, nothing stated in this bulletin is to be taken as a warranty either expressed or implied. FREUI Chem-Trend L.P. 11445 W, McPherson Park | Howell, Michigan 122116 958 FREUDENBERG Yel 517.546.4520 | U.S./Canada: 800-727-7730 | Fax: 517-548-8370 | ChemTrend.com Copyright Chem-Trend L.P,, All Rights Reserved