by | Sep 27, 2025
Technical Data Sheet
son Styrene Free Polyester Gel Coat
fw Premium high temperature system
eee
Description
APG 1750 S is a blend of specially formulated high temperature resins, color pigments, and additives designed to
produce high gloss mold surfaces. APG 1750 S allows for rapid build-up of gel coat and gives hard, durable,
impact and chemical resistant tools and molds. Back-up reinforcement may be applied after a firm gel is obtained.
This normally takes about 75 115 minutes after application. It is most commonly used in high temperature tools
for epoxy infusion, cultured marble molds, thermoforming molds, FRP molds, and RTM mold repair. It contains no
styrene and is low odor.
Properties
e High gloss Impact and chemical resistant
e Rapid build up Excellent finishing and machinability
e High service temperature Epoxy backing materials bond well
e Styrene-free
PHYSICAL PROPERTIES
Ine tt |
Neutral, Orange, or Neutral, Orange, or
feo Taso | cottees | Nec |
Density at 77 F (25 C) 1.30 (10.7) 1.20 (10.00) 1.30 (10.7)
Processing Conditions
e Thoroughly blend 100 parts resin with 2 parts catalyst at indicated ratio for 1 to 1 % minutes in a clean dry
container.
Carefully scrape the surfaces while blending to ensure complete mixing and uniformity.
Surface Preparation and Application
APG 1750 S should always be applied to properly prepared surfaces with mold release applied to surfaces as
necessary.
Product is designed to be applied by brush, flow coating or spray (has been successfully applied with an ES
Manufacturing G860 HVLP spray gun at 40-60psi with a 2.5mm nozzle).
For best performance, APG 1750 S_ should be sprayed in multiple passes of 0.003 0.006 inches (0.07
0.15 mm) film thickness each to a final film thickness of 0.025 inches (0.6 mm). Wait 2 3 minutes between
passes. This technique minimizes air entrapment and pinholes in the gel coat.
Page 1/2- October 6, 2017 US Rev 05
Set 50.8207 Steerisowsse San anzsseorsos1 Nwongsvomz5 Ver se4asz5s1 France
Apemeno imarteong chnad@excon.con__lonkagtade ska.com inaininglersonm somgiecsent Sitcjspandecsoacom | Gobal Headquarters
Lu Imarketing@axson com.mx axson sk@axson.com spain@axson.com salesutiarson.com |_Stson-technclogies.com
by | Sep 27, 2025
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
7/28/2023 ISO 9001:2015 Registered Company
DURA-KOTE GEL COATS
23XX-XXXM
World Class Coatings
Technology
ELITE LOW VOC COLOR GEL COAT
____________________________________________________________________________________________
Dura-kote Elite Marine gel coat all colors is a low VOC, acrylic modified ISO/NPG polyester gel coat. Dura-
Kote Elite gel coats offer a further improvement in UV stability compared to the Advantage line without
compromising other properties. Elite gel coats should be used where color stability is a primary concern and are
suitable for a wide range of applications including boats, recreational vehicles and a variety of industrial
applications.
PERFORMANCE BENEFITS
Good sag resistance
Excellent flow and leveling
Resistance to pinholing
Superior air release
Excellent UV stability
Good impact resistance
TYPICAL LIQUID GEL COAT PROPERTIES
Gel time @77F, 2% MEKP . 18-24 minutes
Viscosity @ 77F, 20RPM #4 spindle … 5,200-5,800cps
Thixotropic Index . 5.5 minimum
Weight per gallon .. 10+1 lbs/gal (color dependent)
Maximum VOC … <33% by weight volatile
<30% by weight for whites and off whites
(Local regulations vary. Consult your local AQMD to determine actual VOC in use)
USAGE GUIDELINES
Mix this product for at least 5 minutes at low speed prior to use
MEKP levels should be kept at 2%
Do not apply gel coats below 64F
Apply using airless spray at a the lowest possible pressure
Film thickness must be between 15mils and 25mils in 2-3 passes with a short flash off time between passes
SHELF LIFE
This product is stable for six months from date of production when stored away from sunlight at no more than 77F.
Extended storage will result in some drift in gel times and viscosity. Elevated temperatures will reduce shelf life
further
by | Sep 27, 2025
Technical Data Sheet
son J Styrene Free Polyester Gel Coat
Premium high temperature system
EEE
Description
APG 1750 S is a blend of specially formulated high temperature resins, color pigments, and additives designed to
produce high gloss mold surfaces. APG 1750 S allows for rapid build-up of gel coat and gives hard, durable,
impact and chemical resistant tools and molds. Back-up reinforcement may be applied after a firm gel is obtained.
This normally takes about 75 115 minutes after application. It is most commonly used in high temperature tools
for epoxy infusion, cultured marble molds, thermoforming molds, FRP molds, and RTM mold repair. It contains no
styrene and is low odor.
Properties
High gloss e Impact and chemical resistant
e Rapid build up e Excellent finishing and machinability
e High service temperature e Epoxy backing materials bond well
e Styrene-free
PHYSICAL PROPERTIES
a
Color Neutral, Orange, or Colorless Neutral, Orange, or
Black Black
Density at 77 F (25 C) 1.30 (10.7) 1.20 (10.00) 1.30 (10.7)
Processing Conditions
Thoroughly blend 100 parts resin with 2 parts catalyst at indicated ratio for 1 to 1 % minutes in a clean dry
container.
e Carefully scrape the surfaces while blending to ensure complete mixing and uniformity.
Surface Preparation and Application
e APG 1750 S should always be applied to properly prepared surfaces with mold release applied to surfaces as
necessary.
e Product is designed to be applied by brush, flow coating or spray (has been successfully applied with an ES
Manufacturing G860 HVLP spray gun at 40-60psi with a 2.5mm nozzle).
e For best performance, APG 1750 S_ should be sprayed in multiple passes of 0.003 0.006 inches (0.07
0.15 mm) film thickness each to a final film thickness of 0.025 inches (0.6 mm). Wait 2 3 minutes between
passes. This technique minimizes air entrapment and pinholes in the gel coat.
Page 1/2- October 6, 2017 US Rev 05
cua GERMANY, toi ray JAPAN ERance
StkaAxson US 021 58.68 30.97 $49 (0) 7125 940 492 $9120 255607 10-11 13902 96 7023.26 481 568 2625 91
sz S00 2270 Marketing. ewne@acon com _tolngadesa com inoindagaconsom ___axsoneatsont Stesjesan@acincom | Clbal Headquarters
axsonmm@axcon.com | “MEXICO SLOVAKIA SPAIN UK Rote otunened
sikaaxson us 15255 82 6649.22 421 7642 25 28 #34932 25 16.20 14416 386600 62 engeen m
marketing axson.com me arson sk@axson.com spain@axson.cam sales. uk@axson.com
by | Sep 27, 2025
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
by | Sep 27, 2025
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
by | Sep 27, 2025
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
by | Sep 27, 2025
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
by | Sep 27, 2025
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
by | Sep 27, 2025
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
by | Sep 27, 2025
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special , incidental or consequential damages
9/4/2020 ISO 9001:2015Registered Company
DURAKOTE GEL COATS
400 SERIES
TOOLING GEL COAT
World Class Coatings
Technology
____________________________________________________________________________________________
Durakote 400 Series Gel Coats are tooling gel coats for fiber glass mold manufacturing. Easy application and
good surface properties make these products suitable for a wide range of tooling applications. Available in clear,
black, red and green, all colors are heavy metal free. Dura-Kote tooling gel coat is also available in a high flex
version as clear (404-009) and green (406-009).
PERFORMANCE BENEFITS
High Gloss
Excellent Hardness
Excellent chemical and abrasion resistance
Minimum distortion
TYPICAL LIQUID GEL COAT PROPERTIES
Gel time @77F, 2% MEKP: 8.5 1.5mins
Viscosity @ 77F, 20RPM # spindle: 3200 250cps
Thixotropic Index: 5 plus
Weight per gallon: 8.8 lbs
Maximum VOC < 45.12%
Maximum HAPs < 40.8
(Local regulations vary. Consult your local AQMD to determine actual VOC in use)
CURED FILM PROPERTIES
Barcol Hardness: 34 +
HDT 200F +
USAGE GUIDELINES
Mix this product for at least 5 minutes at low speed prior to use
MEKP levels should be kept at 2%
Do not apply gel coats below 64F
Apply using airless spray at a the minimum practicable pressure
Film thickness must be between 15mils and 25mils in 2-3 passes with a short flash off time between passes
SHELF LIFE
This product is stable for three months from date of production when stored away from sunlight at no more than
77F. Extended storage will result in some drift in gel times and viscosity. Elevated temperatures will reduce shelf
life further
